- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1351LKTTN-T (Allegro Microsystems Inc)IC SENSOR HALL EFFECT 4-SIP Datasheet資料下載
參數資料
| 型號： | A1351LKTTN-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 19/24頁 |
| 文件大小： | 663K |
| 描述： | IC SENSOR HALL EFFECT 4-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 1 |
| 傳感范圍： | 0.055% ~ 0.095% DC/G |
| 類型： | 線性 - 單極，雙極 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 電流 - 輸出（最大）： | 1mA |
| 輸出類型： | 數字，推挽式 |
| 特點： | 高精度 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1139 (CN2011-ZH PDF) |
| 其它名稱： | 620-1228-6 |
A1351
High Precision Linear Hall Effect Sensor IC
with a Push/Pull, Pulse Width Modulated Output
18
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Try Mode
Try mode allows a single programmable parameter to be tested
without permanently setting its value. (Note that multiple param-
eters cannot be tested simultaneously with the A1351 device.)
Try mode is a required step of parameter blowing. (See the Blow
Mode section for additional information.) After powering the
VCC supply, select the desired parameter register and address its
bit field. When addressing the bit field, each V
PM
pulse incre-
ments the value of the parameter register, up to the maximum
possible code (see the Programming Logic table). The addressed
parameter value remains stored in the device even after the
programming drive voltage is removed from the PWMOUT pin,
allowing the value to be measured. Note that for accurate pro-
gramming, the blow capacitor, C
BLOW
, should be replaced with
the application load capacitance, C
L
, during output voltage mea-
surement. It is not possible to decrement the value of the register
without resetting the parameter bit field. To reset the bit field, and
thus the value of the programmable parameter, cycle the supply
(VCC) voltage.
Blow Mode
After the required value of the programmable parameter is found
using Try mode, its corresponding code should be blown to make
its value permanent. To do this, select the required parameter
register, and address and blow each required bit separately (as
described in the Fuse Blowing section). The supply must be
cycled between blowing each bit of a given code. After a bit is
blown, cycling the supply will not reset its value.
Lock Mode
To lock the device, address the LOCK bit and apply a blow pulse
with C
BLOW
in place. The LOCK bit is located in register 5, code
512. After locking the device, no future programming of any
parameter is possible.
Programming Modes
相關PDF資料 |
PDF描述 |
|---|---|
| A1354KKT-T | IC SENSOR HALL EFFECT 4-SIP |
| A1356LKB-T | IC SENSOR HALL EFFECT 3 SIP |
| A1361LKTTN-T | IC HALL EFFECT SENSOR LN 4-SIP |
| A1374EKB-T | IC SENSOR HALL EFFECT PREC 3-SIP |
| A1422LK | IC SENSOR HALL EFFECT AC 4-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1352-035 | 制造商:AVX Corporation 功能描述: |
| A1352-037 | 制造商:AVX Corporation 功能描述: |
| A13532-43N | 制造商:Harris Corporation 功能描述: |
| A1354 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision 2-Wire Linear Hall Effect Sensor IC with Pulse Width Modulated Output |
| A13546-000 | 制造商:TE Connectivity 功能描述:VARISTOR 680V 20MM RADIAL 制造商:TE Connectivity 功能描述:VARISTOR 680V 10KA DISC 20MM 制造商:TE CONNECTIVITY RAYCHEM-POLYSWITCH 功能描述:Var MOV 420VAC 560VDC 10000A 680V Thru-Hole Bulk |
發布緊急采購，3分鐘左右您將得到回復。