- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1356LKB-T (Allegro Microsystems Inc)IC SENSOR HALL EFFECT 3 SIP Datasheet資料下載
參數資料
| 型號： | A1356LKB-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 14/20頁 |
| 文件大小： | 432K |
| 描述： | IC SENSOR HALL EFFECT 3 SIP |
| 標準包裝： | 4,000 |
| 傳感范圍： | 45m%D/G ~ 75m%D/G |
| 類型： | 線性 - 可編程 |
| 電源電壓： | 4.5 V ~ 18 V |
| 電流 - 電源： | 10mA |
| 電流 - 輸出（最大）： | 25mA |
| 輸出類型： | 數字式， PWM 編碼 |
| 特點： | 高精度 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
| 其它名稱： | 620-1369 A1356LK-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁
High Precision Linear Hall-Effect Sensor IC
With an Open Drain Pulse Width Modulated Output
A1356
14
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
and blown. An appropriate sequence for blowing code 5 is shown
in figure 7. The order of blowing bits, however, is not important.
Blowing bit 0 first, and then bit 2 is acceptable.
Note: After blowing, the programming is not reversible, even
after cycling the supply power. Although a register bit field fuse
cannot be reset after it is blown, additional bits within the same
register can be blown at any time until the device is locked. For
example, if bit 1 (binary 10) has been blown, it is still possible to
blow bit 0. The end result would be binary 11 (decimal code 3).
Locking the Device
After the desired code for each parameter is programmed, the
device can be locked to prevent further programming of any
parameters.
Additional Guidelines
The additional guidelines in this section should be followed to
ensure the proper behavior of these devices:
" A 0.1 糉 blowing capacitor, C
BLOW
, must be mounted between
the supply pin and the GND pin during programming, to ensure
enough current is available to blow fuses.
" The application capacitance, C
L
, should be used when measur-
ing the output duty cycle during programming.
" The power supply used for programming must be capable of
delivering at least 26 V and 300 mA.
" Be careful to observe the t
LOW
delay time before powering
down the device after blowing each bit.
" The following programming order is recommended:
1. f
PWM
2. Sens
3. D
(Q)
4. Lock the device (only after all other parameters have been
programmed and validated, because this prevents any further
programming of the device)
Programming Modes
Try Mode Try mode allows multiple programmable parameters
to be tested simultaneously without permanently setting any
values. In this mode, each V
P(HIGH)
pulse will indefinitely loop
the programming logic through the mode, register, and bit field
selection states.
After powering the V
CC
supply, select mode key 2, the desired
parameter register, and address its bit field. When addressing the
bit field, each V
P(MID)
pulse increments the value of the param-
eter register up to the maximum possible code (see Programming
Logic section). The addressed parameter value is stored in the
device even after the programming drive voltage is removed from
Figure 6. Example of code 5 broken into its binary components, which are
code 4 and code 1.
Figure 7. Example of Blow Mode programming pulses applied to the VCC pin. In this example, DC(Q)
(Parameter Key 2) is addressed to code 4 (i.e bit 2) and its value is permanently blown.
(Decimal Equivalent)
Code 5
Bit Field Selection
Address Code Format
Code in Binary
Fuse Blowing
Target Bits
Fuse Blowing
Address Code Format
(Binary)
1 0 1
Bit 2
Bit 0
Code 4 Code 1
(Decimal Equivalents)
V+
0
Mode
Selection
Parameter
Selection
(Key 1)
V
P(HIGH)
V
P(MID)
V
P(LOW)
(Key 2)
(Code 4)
Addressing
Bitfield 2
t
BLOW
Code 4
Blow
t
Low
Cycle VCC
supply
Cycle VCC
supply
1
1 2
1 2 3 4
相關PDF資料 |
PDF描述 |
|---|---|
| A1361LKTTN-T | IC HALL EFFECT SENSOR LN 4-SIP |
| A1374EKB-T | IC SENSOR HALL EFFECT PREC 3-SIP |
| A1422LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1425LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1645LK-I2 | IC SENSOR HALL EFFECT AC 4-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1357 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Two-Wire High Precision Linear Hall-Effect Sensor IC |
| A1357LKB-T | 功能描述:IC HALL EFFECT SWITCH 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1358 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TRANSISTOR (AUDIO FREQUENCY POWER AMPLIFIER APPLICATIONS) |
| A-1358 | 功能描述:通用繼電器 DC SOLENOID. RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| A13580-000 | 制造商:TE Connectivity 功能描述:Cable Markers Yellow Pack 制造商:TE Connectivity 功能描述:HTCM-SCE-TP-1/4-4H-4 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。