- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1361LKTTN-T (Allegro Microsystems Inc)IC HALL EFFECT SENSOR LN 4-SIP Datasheet資料下載
參數資料
| 型號： | A1361LKTTN-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 22/26頁 |
| 文件大小： | 618K |
| 描述： | IC HALL EFFECT SENSOR LN 4-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 1 |
| 傳感范圍： | 1.4mV/G ~ 4.5mV/G |
| 類型： | 線性 - 單極，雙極 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 12mA |
| 電流 - 輸出（最大）： | 10mA |
| 輸出類型： | 模擬，比率 |
| 特點： | 可編程 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1139 (CN2011-ZH PDF) |
| 其它名稱： | 620-1234-6 |
A1360, A1361,
and A1362
To construct a current sensor using the A136x, first consider a
current carrying wire that we want to observe. As dictated by
Amperes Law, a magnetic field is produced around the wire
that is proportional to the amount of current flowing through
the wire. By passing this wire through a soft magnetic core, the
magnetic flux produced by the wire can be concentrated and
directed through a gap in the core. The magnetic flux density can
be measured by inserting the A136x SIP into the gap in the core.
As a result, the output of the A136x device will be proportional
to the amount of current flowing through the wire.
The example feedthrough current sensing setup shown below
(figure 7) has a core made of mu metal that is 2 mm thick
and 4 mm wide. The inner radius of the core is 14.5 mm and
the outer radius is 18.5 mm. The wire going through the center
of the core has a radius of 9 mm. Using this setup with a gap of
1.7 mm, a field strength results that is on the order of 7 G / A at
the Hall element in the A136x.
The recommended core material for construction of the concen-
trator depends on the specific application. If high flux saturation
is desired, then an alloy such as HyPerm49 is recommended.
For lower-current level sensing applications, a material such as
HyMu80 may be desired. (HyMu80 has lower magnetic flux
saturation than HyPerm49, therefore more HyMu80 mate-
rial is required to carry the same amount of flux compared
to Hyperm49.) If frequency response is a concern, then eddy
currents can be reduced by either laminating the HyPerm49 or
HyMu80 alloys, or by using a ferrite core.
Constructing a Current Sensor Using the A136x
?8 mm
4 mm
2 mm
?7 mm
Application-specific housing
Ring concentrator
Current-conducting wire
A136x
Center Hall element in gap
1.7 mm
Figure 7. The example current sensor setup used to generate the data in this section was
constructed with a split-ring concentrator and an A136x device. A copper wire was fed
through the concentrator, and the A136x placed in its gap. This approximates a typical
ammeter application on a thick wire, such as shown in the left view. Note that such
applications usually have a protective housing, which should be taken into consideration
when designing the nal application. The housing is beyond the scope of this example.
Low-Noise Programmable Linear Hall Effect Sensor ICs with
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
22
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| A1374EKB-T | IC SENSOR HALL EFFECT PREC 3-SIP |
| A1422LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1425LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1645LK-I2 | IC SENSOR HALL EFFECT AC 4-SIP |
| A3230LUA-T | IC SW HALL EFFECT CHOPPER 3-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1362LKTTN-T | 功能描述:IC HALL EFFECT SENSOR LN 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1363LKTTN-10-T | 功能描述:IC HALL SENSOR 6.4-14MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-1-T | 功能描述:IC HALL SENSOR 0.6-1.3MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:模塊 標準包裝:1 |
| A1363LKTTN-2-T | 功能描述:IC HALL SENSOR 1.3-2.9MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-5-T | 功能描述:IC HALL SENSOR 2.9-6.4MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。