- 您現在的位置：買賣IC網 > PDF目錄373913 > AD7675AST (ANALOG DEVICES INC) 16-Bit, 100 kSPS, Differential ADC PDF資料下載
參數資料
| 型號： | AD7675AST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 100 kSPS, Differential ADC |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP48 |
| 封裝： | 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 5/20頁 |
| 文件大小： | 399K |
| 代理商： | AD7675AST |
REV. 0
AD7675
–
5
–
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Type
Description
1
2
3, 6, 7,
40–42,
44–48
4
AGND
AVDD
NC
P
P
Analog Power Ground Pin
Input Analog Power Pins. Nominally 5 V.
No Connect
BYTESWAP
DI
Parallel Mode Selection (8/16 Bit). When LOW, the LSB is output on D[7:0] and the MSB is
output on D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Two’s Complement. When OB/
2C
is HIGH, the digital output is
straight binary; when LOW, the MSB is inverted resulting in a two’s complement output
from its internal shift register.
Serial/Parallel Selection Input. When LOW, the parallel port is selected; when HIGH, the
serial interface mode is selected and some bits of the DATA bus are used as a serial port.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/
PAR
is HIGH, these outputs are
in high impedance.
When SER/
PAR
is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port
Data Output Bus.
When SER/
PAR
is HIGH, EXT/
INT
is LOW and RDC/SDIN is LOW which is the serial
master read after convert mode. These inputs, part of the serial port, are used to slow down, if
desired, the internal serial clock which clocks the data output. In the other serial modes, these
inputs are not used.
When SER/
PAR
is LOW, this output is used as the Bit 4 of the Parallel Port Data Output Bus.
When SER/
PAR
is HIGH, this input, part of the serial port, is used as a digital select input for
choosing the internal or an external data clock. With EXT/
INT
tied LOW, the internal clock
is selected on SCLK output. With EXT/
INT
set to a logic HIGH, output data is synchronized
to an external clock signal connected to the SCLK input.
When SER/
PAR
is LOW, this output is used as the Bit 5 of the Parallel Port Data Output Bus.
When SER/
PAR
is HIGH, this input, part of the serial port, is used to select the active state of
the SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
When SER/
PAR
is LOW, this output is used as the Bit 6 of the Parallel Port Data Output Bus.
When SER/
PAR
is HIGH, this input, part of the serial port, is used to invert the SCLK signal.
It is active in both master and slave mode.
When SER/
PAR
is LOW, this output is used as the Bit 7 of the Parallel Port Data Output Bus.
When SER/
PAR
is HIGH, this input, part of the serial port, is used as either an external data
input or a read mode selection input depending on the state of EXT/
INT
.
When EXT/
INT
is HIGH, RDC/SDIN could be used as a data input to daisy chain the con-
version results from two or more ADCs onto a single SDOUTline. The digital data level on
SDIN is output on DATA with a delay of 16 SCLK periods after the initiation of the read
sequence. When EXT/
INT
is LOW, RDC/SDIN is used to select the read mode. When RDC/
SDIN is HIGH, the data is output on SDOUT during conversion. When RDC/SDIN is LOW,
the data is output on SDOUT only when the conversion is complete.
Input/Output Interface Digital Power Ground
Input/Output Interface Digital Power. Nominally at the same supply than the supply of the
host interface (5 V or 3 V).
Digital Power. Nominally at 5 V.
Digital Power Ground
5
OB/
2C
DI
8
SER/
PAR
DI
9, 10
DATA[0:1]
DO
11, 12
DATA[2:3] or
DI/O
DIVSCLK[0:1]
13
DATA[4]
or EXT/
INT
DI/O
14
DATA[5]
or INVSYNC
DI/O
15
DATA[6]
or INVSCLK
DI/O
16
DATA[7]
or RDC/SDIN
DI/O
17
18
OGND
OVDD
P
P
19
20
DVDD
DGND
P
P
相關PDF資料 |
PDF描述 |
|---|---|
| AD7675ASTRL | 16-Bit, 100 kSPS, Differential ADC |
| AD7676 | 16-Bit +-1 LSB INL, 500 kSPS, Differential ADC |
| AD7676AST | 16-Bit +-1 LSB INL, 500 kSPS, Differential ADC |
| AD7676ASTRL | 16-Bit +-1 LSB INL, 500 kSPS, Differential ADC |
| AD7677 | 16-Bit, 1 LSB INL, 1 MSPS Differential ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7675ASTRL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LQFP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 16BIT PARALLEL/SERL 48LQFP - Tape and Reel |
| AD7675ASTZ | 功能描述:IC ADC 16BIT DIFF INP 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7675ASTZRL | 功能描述:IC ADC 16BIT DIFF INP 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7676 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit +-1 LSB INL, 500 kSPS, Differential ADC |
| AD7676ACP | 制造商:Analog Devices 功能描述:ADC SGL SAR 500KSPS 16BIT PARALLEL/SERL 48LFCSP - Trays |
發布緊急采購，3分鐘左右您將得到回復。