欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68360RC25
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: QUad Integrated Communications Controller Users Manual
中文描述: RISC MICROCONTROLLER, CPGA241
封裝: PGA-241
文件頁數: 27/28頁
文件大小: 159K
代理商: MC68360RC25
MOTOROLA
MC68360 USER’S MANUAL ERRATA
27
5. Phase Jitter Performance.
The phase jitter of the PLL is defined as the variations in the skew between the rising edges
of EXTAL and CLKO1/2 for a given device in specific temperature, voltage, input frequency,
MF, and capacitive load on CLKO1/2. These variations are result of the PLL locking
mechanism. For input frequencies greater than 10MHZ and MF<=4, this jitter is less than +/
-1.0ns. Otherwise, this jitter is not guaranteed. However, for MF<10 and input frequencies
greater than 10MHz this jitter is less than +/-2.6ns.
6. Frequency Jitter Performance.
The frequency jitter of the PLL is defined as the variation of the frequency of CLKO1/2. For
small MF (MF<10) this jitter is smaller than 0.5%. For mid-range MF (10 < MF < 500) this
jitter is between 0.5% and ~2%. For large MF (MF > 500), the frequency jitter is 2-3%.
7. Input (EXTAL) Jitter Requirements.
The allowed jitter on the frequency of EXTAL is 0.5%. If the rate of change of the frequency
at EXTAL is slow (i.e. it does not jump between the min and max values in one cycle) or the
frequency of the jitter is fast (i.e. it does not stay at an extreme value for a long time) then
the allowed jitter can be 2%. The phase and frequency jitter performance results are only
valid if the input jitter is less than the prescribed values.
8. K-Factor for A.C. Specification.
The following numbers should be used to estimate derating of load capacitance.
a. K-factor for decreasing load (less then 100pf) = 0.2 [ns/10Pf]
b. K-factor for increasing load (more then 100pf) = 0.6 [ns/10pf]
9. Low Frequency Oscillator Use.
The output of the Voltage Controlled Oscillator (VCO) shown in Figure 6-5 is twice the
resultant clock of the PLL. Thus, a 25 MHz clock yields a VCO output of 50 MHz. If a user
wishes to use a low speed clock, the output of VCO must be at least 10 MHz. If the MODCK
values of 11 or 10 are used, the default multiplication factor is 401. Therefore, the lowest
speed input clock that can be used is 12 kHz. However, the system can operate with even
slower system frequency (slower than 12 kHz). This can be achieved by dividing down the
clock using the CDVCR. If the user chooses this method, the following conditions apply:
(a). EXTAL and QUICC internal clock phases will not be synchronized.
(b). CLKO1 will not be a 50% duty cycle.
(c). CLKO2 output (if enabled) will be the frequency of PLL's output before division.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC68360RC25V QUad Integrated Communications Controller Users Manual
MC68360RC33 QUad Integrated Communications Controller Users Manual
MC68360ZP25 QUad Integrated Communications Controller Users Manual
MC68040 Errata and Added Information to MC68360 Quad Integrated Communication Controller User Manual Rev 1
MC68360 32-Bit Microprocessor(32位微處理器)
相關代理商/技術參數
參數描述
MC68360RC25L 功能描述:微處理器 - MPU QUICC, SIM, 4SCC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68360RC25V 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:QUad Integrated Communications Controller Users Manual
MC68360RC33 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:QUad Integrated Communications Controller Users Manual
MC68360RC33L 功能描述:微處理器 - MPU QUICC SIM 4SCC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68360TUT 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:TUTORIAL A QUICC-START
主站蜘蛛池模板: 九龙县| 海城市| 山阴县| 芒康县| 辉南县| 长乐市| 延津县| 无棣县| 醴陵市| 盐山县| 启东市| 息烽县| 宁德市| 蓝田县| 盘山县| 鄢陵县| 洛南县| 南京市| 四会市| 永登县| 大兴区| 定兴县| 房山区| 吉木萨尔县| 登封市| 大冶市| 镇平县| 泗洪县| 闵行区| 阿鲁科尔沁旗| 勃利县| 屯留县| 彭阳县| 曲水县| 深圳市| 昔阳县| 双峰县| 连城县| 丰都县| 肇源县| 宣恩县|