- 您現在的位置：買賣IC網 > PDF目錄192295 > S25FL004D0LNAI013 (Spansion Inc.) 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface PDF資料下載
參數資料
| 型號： | S25FL004D0LNAI013 |
| 廠商： | Spansion Inc. |
| 英文描述： | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| 中文描述： | 4兆位的CMOS閃存3.0伏，50赫茲的SPI總線接口 |
| 文件頁數： | 13/36頁 |
| 文件大小： | 724K |
| 代理商： | S25FL004D0LNAI013 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
20
S25FL Family (Serial Peripheral Interface) S25FL004D
S25FL004D_00A0 June 28, 2004
Ad va n c e
In f o rm a t i o n
the Status Register may be read to check the value of the Write In Progress (WIP)
bit. The Write In Progress (WIP) bit is 1 during the self-timed Page Program cycle,
and is 0 when it is completed. At some unspecified time before the cycle is com-
pleted, the Write Enable Latch (WEL) bit is reset.
A Page Program (PP) instruction applied to a page that is protected by the Block
Protect (BP2, BP1, BP0) bits (see Table 1) is not executed.
Figure 11. Page Program (PP) Instruction Sequence
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh) all bits inside the chosen sector.
Before it can be accepted, a Write Enable (WREN) instruction must previously
have been executed. After the Write Enable (WREN) instruction has been de-
coded, the device sets the Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by driving Chip Select (CS#) Low,
followed by the instruction code, and three address bytes on Serial Data Input
(SI). Any address inside the Sector (see Table 1) is a valid address for the Sector
Erase (SE) instruction. Chip Select (CS#) must be driven Low for the entire du-
ration of the sequence.
The instruction sequence is shown in Figure 12.
Chip Select (CS#) must be driven High after the eighth bit of the last address byte
has been latched in, otherwise the Sector Erase (SE) instruction is not executed.
As soon as Chip Select (CS#) is driven High, the self-timed Sector Erase cycle
(whose duration is tSE) is initiated. While the Sector Erase cycle is in progress,
the Status Register may be read to check the value of the Write In Progress (WIP)
bit. The Write In Progress (WIP) bit is 1 during the self-timed Sector Erase cycle,
0
34
33
32
31
30
29
28
10
9
8
7
6
5
4
3
2
1
35 36 37 38 39
46
45
44
43
42
41
40
47 48 49 50 51 52 53 54 55
2073
2072
2076
2075
2074
2079
2078
2077
23 22 21
3
21
07
6
5
43
2
1
0
Data Byte 1
24-Bit Address
Instruction
Data Byte 2
Data Byte 3
Data Byte 256
MSB
SCK
SI
SCK
SI
7
65
4
3
2
1
0
76
54
32
1
0
7
6
5
432
10
CS#
相關PDF資料 |
PDF描述 |
|---|---|
| S25FL064A0LNAI00 | 64M X 1 FLASH 3V PROM, PDSO16 |
| S2684-254 | PHOTO DIODE |
| S2815S | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| S29AL032D70BAE000 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D70BAE002 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL004D0LNFI011 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004D0LNFI013 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004K0XMFI010 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI011 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 4MBIT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。