- 您現在的位置：買賣IC網 > PDF目錄192295 > S25FL004D0LNAI013 (Spansion Inc.) 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface PDF資料下載
參數資料
| 型號： | S25FL004D0LNAI013 |
| 廠商： | Spansion Inc. |
| 英文描述： | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| 中文描述： | 4兆位的CMOS閃存3.0伏，50赫茲的SPI總線接口 |
| 文件頁數： | 19/36頁 |
| 文件大小： | 724K |
| 代理商： | S25FL004D0LNAI013 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
26
S25FL Family (Serial Peripheral Interface) S25FL004D
S25FL004D_00A0 June 28, 2004
Ad va n c e
In f o rm a t i o n
Power-up and Power-down
The device must not be selected at power-up or power-down (that is, CS# must
follow the voltage applied on VCC) until VCC reaches the correct value as follows:
VCC (min) at power-up, and then for a further delay of tPU (as described in
VSS at power-down
A simple pull-up resistor on Chip Select (CS#) can usually be used to insure safe
and proper power-up and power-down.
old. However, correct operation of the device is not guaranteed if by this time VCC
is still below VCC (min). No Write Status Register, Program or Erase instructions
At power-up, the device is in Standby mode (not Deep Power Down mode) and
the WEL bit is reset.
During Power-down or voltage drops, the power down must drop below the VCC
(low) for a period of minimum tPD for the device to initialize correctly on power
up. (See Figure 18).
Normal precautions must be taken for supply rail decoupling to stabilize the VCC
feed. Each device in a system should have the VCC rail decoupled by a suitable
capacitor close to the package pins (this capacitor is generally of the order of 0.1
F).
At power-down, when VCC drops from the operating voltage to below the mini-
mum VCC threshold, all operations are disabled and the device does not respond
to any instructions. (The designer needs to be aware that if a power-down occurs
while a Write, Program or Erase cycle is in progress, data corruption can result.)
相關PDF資料 |
PDF描述 |
|---|---|
| S25FL064A0LNAI00 | 64M X 1 FLASH 3V PROM, PDSO16 |
| S2684-254 | PHOTO DIODE |
| S2815S | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| S29AL032D70BAE000 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D70BAE002 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL004D0LNFI011 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004D0LNFI013 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004K0XMFI010 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI011 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 4MBIT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。