欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S25FL004D0LNFI013
廠商: SPANSION LLC
元件分類: PROM
英文描述: 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
中文描述: 4M X 1 FLASH 3V PROM, DSO8
封裝: 6 X 5 MM, LEAD FREE, MO-229, WSON-8
文件頁數: 17/36頁
文件大小: 724K
代理商: S25FL004D0LNFI013
24
S25FL Family (Serial Peripheral Interface) S25FL004D
S25FL004D_00A0 June 28, 2004
Ad va n c e
In f o rm a t i o n
Figure 15. Release from Deep Power Down Instruction Sequence
Release from Deep Power Down and Read Electronic Signature (RES)
Once the device has entered Deep Power Down mode, all instructions are ignored
except the RES instruction. The RES instruction can also be used to read the 8-
bit Electronic Signature of the device on the SO pin. The RES instruction always
provides access to the Electronic Signature of the device (except while an Erase,
Program or WRSR cycle is in progress), and can be applied even if DP mode has
not been entered. Any RES instruction executed while an Erase, Program or
WRSR cycle is in progress is not decoded, and has no effect on the cycle in
progress.
The device features an 8-bit Electronic Signature, whose value for the S25FL004D
is 12h. This can be read using RES instruction.
The device is first selected by driving Chip Select (CS#) Low. The instruction code
is followed by 3 dummy bytes, each bit being latched-in on Serial Data Input (SI)
during the rising edge of Serial Clock (SCK). Then, the 8-bit Electronic Signature,
stored in the memory, is shifted out on Serial Data Output (SO), each bit being
shifted out during the falling edge of Serial Clock (SCK).
The instruction sequence is shown in Figure 16.
The Release from Deep Power Down and Read Electronic Signature (RES) is ter-
minated by driving Chip Select (CS#) High after the Electronic Signature has
been read at least once. Sending additional clock cycles on Serial Clock (SCK),
while Chip Select (CS#) is driven Low, causes the Electronic Signature to be out-
put repeatedly.
When Chip Select is driven High, the device is put in the Stand-by Power mode.
If the device was not previously in the Deep Power Down mode, the transition to
the Stand-by Power mode is immediate. If the device was previously in the Deep
Power Down mode, though, the transition to the Standby mode is delayed by
tRES, and Chip Select (CS#) must remain High for at lease tRES(max), as specified
in Table 8. Once in the Stand-by Power mode, the device waits to be selected, so
that it can receive, decode and execute instructions.
CS#
SCK
SI
0
1
23
4
5
6
7
Instruction
Deep Power Down Mode
t
RES
Standby Mode
相關PDF資料
PDF描述
S25FL004D 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNAI011 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL004D0LNAI013 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
S25FL064A0LNAI00 64M X 1 FLASH 3V PROM, PDSO16
S2684-254 PHOTO DIODE
相關代理商/技術參數
參數描述
S25FL004K0XMFI010 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S25FL004K0XMFI011 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S25FL004K0XMFI013 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 4MBIT - Bulk
S25FL004K0XMFI040 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S25FL004K0XMFI041 制造商:Spansion 功能描述:IC 4-MBIT CMOS 3.0 VOLT FLASH MEMORY 104MHZ SPI - Bulk
主站蜘蛛池模板: 伊春市| 射洪县| 太原市| 天水市| 九龙县| 扶绥县| 昌邑市| 和田县| 江油市| 手游| 呼和浩特市| 德兴市| 邢台市| 介休市| 高邑县| 西安市| 青神县| 马关县| 石楼县| 镇平县| 通州区| 浦城县| 岳阳市| 威海市| 靖远县| 澄城县| 巴林左旗| 繁峙县| 本溪市| 大方县| 会泽县| 防城港市| 黄龙县| 嘉禾县| 揭东县| 连山| 江北区| 乾安县| 玉屏| 丹凤县| 潮州市|