- 您現在的位置：買賣IC網 > PDF目錄192295 > S25FL004D0LNFI013 (SPANSION LLC) 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface PDF資料下載
參數資料
| 型號： | S25FL004D0LNFI013 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| 中文描述： | 4M X 1 FLASH 3V PROM, DSO8 |
| 封裝： | 6 X 5 MM, LEAD FREE, MO-229, WSON-8 |
| 文件頁數： | 7/36頁 |
| 文件大小： | 724K |
| 代理商： | S25FL004D0LNFI013 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
June 28, 2004 S25FL004D_00A0
S25FL Family (Serial Peripheral Interface) S25FL004D
15
Ad va nc e
In forma t i o n
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be
read. The Status Register may be read at any time, even while a Program, Erase,
or Write Status Register cycle is in progress. When one of these cycles is in
progress, it is recommended to check the Write In Progress (WIP) bit before
sending a new instruction to the device. It is also possible to read the Status Reg-
ister continuously, as shown in Figure 6.
Figure 6. Read Status Register (RDSR) Instruction Sequence
Figure 7. Status Register Format
The status and control bits of the Status Register are as follows:
SRWD bit: The Status Register Write Disable (SRWD) bit is operated in conjunc-
tion with the Write Protect (W#) signal. The Status Register Write Disable
(SRWD) bit and Write Protect (W#) signal allow the device to be put in the Hard-
ware Protected mode (when the Status Register Write Disable (SRWD) bit is set
to 1, and Write Protect (W#) is driven Low). In this mode, the non-volatile bits
of the Status Register (SRWD, BP2, BP1, BP0) become read-only bits and the
Write Status Register (WRSR) instruction is no longer accepted for execution.
BP2, BP1, BP0 bits: The Block Protect (BP2, BP1, BP0) bits are non-volatile.
They define the size of the area to be software protected against Program and
Erase instructions. These bits are written with the Write Status Register (WRSR)
instruction. When one or both of the Block Protect (BP2, BP1, BP0) bits is set to
1, the relevant memory area (as defined in Table 1) becomes protected against
Page Program (PP), and Sector Erase (SE) instructions. The Block Protect (BP2,
BP1, BP0) bits can be written provided that the Hardware Protected mode has not
Instruction
High Impedance
MSB
Status Register Out
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
7 6
5 4 3 2 10
7 6 5 4 3 2 1 0 7
SO
SI
SCK
CS#
Status Register
Write Disable
Block Protect Bits
Write Enable Latch Bit
Write In Progress Bit
SRWD
0
BP2
BP1
BP0
WEL
WIP
b7
b0
相關PDF資料 |
PDF描述 |
|---|---|
| S25FL004D | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004D0LNAI011 | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL004D0LNAI013 | 4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface |
| S25FL064A0LNAI00 | 64M X 1 FLASH 3V PROM, PDSO16 |
| S2684-254 | PHOTO DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL004K0XMFI010 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI011 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 4MBIT - Bulk |
| S25FL004K0XMFI040 | 功能描述:閃存 4-MBIT CMOS 3V FLASH MEMORY 104MHz SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL004K0XMFI041 | 制造商:Spansion 功能描述:IC 4-MBIT CMOS 3.0 VOLT FLASH MEMORY 104MHZ SPI - Bulk |
發布緊急采購，3分鐘左右您將得到回復。