- 您現在的位置：買賣IC網 > PDF目錄192295 > S25FL064A0LNAI00 (SPANSION LLC) 64M X 1 FLASH 3V PROM, PDSO16 PDF資料下載
參數資料
| 型號： | S25FL064A0LNAI00 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 64M X 1 FLASH 3V PROM, PDSO16 |
| 封裝： | 0.300 INCH, PLASTIC, MS-013AA, SOP-16 |
| 文件頁數： | 21/36頁 |
| 文件大?。?/td> | 1495K |
| 代理商： | S25FL064A0LNAI00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
June 29, 2007 S25FL064A_00_C3
S25FL064A
29
Data
She e t
10. Power-up and Power-down
During power-up and power-down, certain conditions must be observed. CS# must follow the voltage applied
on VCC, and must not be driven low to select the device until VCC reaches the allowable values as follows
(see Figure 10.1 and Table 10.1):
At power-up, VCC (min) plus a period of tPU
At power-down, VSS
A pull-up resistor on Chip Select (CS#) typically meets proper power-up and power-down requirements.
No Write Status Register, program, or erase command should be sent to the device until VCC rises to the VCC
min, plus a delay of tPU. At power-up, the device is in standby mode (not Deep Power Down mode) and the
WEL bit is reset (0).
Each device in the host system should have the VCC rail decoupled by a suitable capacitor close to the
package pins (this capacitor is generally of the order of 0.1 F), as a precaution to stabilizing the VCC feed.
When VCC drops from the operating voltage to below the minimum VCC threshold at power-down, all
operations are disabled and the device does not respond to any commands. Note that data corruption may
result if a power-down occurs while a Write Register, program, or erase operation is in progress.
Figure 10.1 Power-Up Timing Diagram
11. Initial Delivery State
The device is delivered with all bits set to 1 (each byte contains FFh) upon initial factory shipment. The Status
Register contains 00h (all Status Register bits are 0).
Table 10.1 Power-Up Timing Characteristics
Symbol
Parameter
Min
Max
Unit
VCC(min)
VCC (minimum)
2.7
V
tPU
VCC (min) to device operation
10
ms
Vcc
(max)
Vcc
(min)
Full Device Access
tPU
Time
相關PDF資料 |
PDF描述 |
|---|---|
| S2684-254 | PHOTO DIODE |
| S2815S | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| S29AL032D70BAE000 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D70BAE002 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL064K | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64-Mbit CMOS 3.0 Volt Flash Memory with 80-MHz SPI (Serial Peripheral Interface) Multi I/O Bus |
| S25FL064K0SMFI010 | 功能描述:閃存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL064K0SMFI011 | 功能描述:閃存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL064K0SMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 64MBIT - Bulk |
| S25FL064LABBHI020 | 功能描述:IC FLASH NOR 24FBGA 制造商:cypress semiconductor corp 系列:FL-L 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:64Mb （8M x 8） 時鐘頻率:108MHz 寫周期時間 - 字，頁:- 存儲器接口:SPI - 四 I/O， QPI 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:24-TBGA 供應商器件封裝:24-BGA（6x8） 標準包裝:338 |
發布緊急采購，3分鐘左右您將得到回復。