- 您現在的位置：買賣IC網 > PDF目錄192295 > S29AL032D70BAE002 (Spansion Inc.) 32 Megabit CMOS 3.0 Volt-only Flash Memory PDF資料下載
參數資料
| 型號： | S29AL032D70BAE002 |
| 廠商： | Spansion Inc. |
| 英文描述： | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| 中文描述： | 32兆位的CMOS 3.0伏只閃存 |
| 文件頁數： | 30/69頁 |
| 文件大小： | 1970K |
| 代理商： | S29AL032D70BAE002 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
34
S29AL032D
S29AL032D_00_A3 June 13, 2005
Advan ce
In form ati o n
NOTE: See Table 17 for program command sequence.
Figure 4. Program Operation
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing
two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then
followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The
device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these oper-
ations. Table 17 on page 38 shows the address and data requirements for the chip erase
command sequence.
Any commands written to the chip during the Embedded Erase algorithm are ignored. Note that
a hardware reset during the chip erase operation immediately terminates the operation. The
Chip Erase command sequence should be reinitiated once the device has returned to reading
array data, to ensure data integrity.
The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#.
See Write Operation Status on page 39 for information on these status bits. When the Embedded
Erase algorithm is complete, the device returns to reading array data and addresses are no longer
latched.
Figure 5, on page 36 illustrates the algorithm for the erase operation. See Erase/Program
Operations on page 54 for parameters, and to Figure 19, on page 56 for timing diagrams.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI043 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29CD016G0JDEI004 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD016G0JDEI007 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD032J1JFAI122 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29AL032D70BAI000 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 32Mbit 4M x 8bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI030 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI032 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA T/R |
| S29AL032D70BFI000 | 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29AL032D70BFI030 | 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。