- 您現在的位置：買賣IC網 > PDF目錄192295 > S29AL032D70BAE002 (Spansion Inc.) 32 Megabit CMOS 3.0 Volt-only Flash Memory PDF資料下載
參數資料
| 型號： | S29AL032D70BAE002 |
| 廠商： | Spansion Inc. |
| 英文描述： | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| 中文描述： | 32兆位的CMOS 3.0伏只閃存 |
| 文件頁數： | 6/69頁 |
| 文件大小： | 1970K |
| 代理商： | S29AL032D70BAE002 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
12
S29AL032D
S29AL032D_00_A3 June 13, 2005
Advan ce
In form ati o n
The internal state machine is set for reading array data upon device power-up, or after a hardware
reset. This ensures that no spurious alteration of the memory content occurs during the power
transition. No command is necessary in this mode to obtain array data. Standard microprocessor
read cycles that assert valid addresses on the device address inputs produce valid data on the
device data outputs. The device remains enabled for read access until the command register con-
tents are altered.
See Reading Array Data on page 31 for more information. Refer to the AC Read Operations on
page 50 table for timing specifications and to Figure 14, on page 50 for the timing diagram. ICC1
in the DC Characteristics table represents the active current specification for reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and
erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH.
For program operations, the BYTE# pin determines whether the device accepts program data in
bytes or words. Refer to Word/Byte Configuration (Models 03, 04 Only) on page 11 for more
information.
The device features an Unlock Bypass mode to facilitate faster programming. Once the device
enters the Unlock Bypass mode, only two write cycles are required to program a word or byte,
instead of four. The Word/Byte Program Command Sequence on page 32 section has details on
programming data to the device using both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 on page 14
and Table 4 on page 16 indicate the address space that each sector occupies. A sector address
consists of the address bits required to uniquely select a sector. The Command Definitions on
page 31 contains details on erasing a sector or the entire chip, or suspending/resuming the erase
operation.
After the system writes the autoselect command sequence, the device enters the autoselect
mode. The system can then read autoselect codes from the internal register (which is separate
from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to
information.
ICC2 in the DC Characteristics table represents the active current specification for the write mode.
AC Characteristics on page 50 contains timing specification tables and timing diagrams for write
operations.
Program and Erase Operation Status
During an erase or program operation, the system may check the status of the operation by read-
ing the status bits on DQ7–DQ0. Standard read cycle timings and ICC read specifications apply.
Refer to Write Operation Status on page 39 for more information, and to AC Characteristics on
page 50 for timing diagrams.
Accelerated Program Operation
The device offers accelerated program operations through the ACC function. This is one of two
functions provided by the WP#/ACC (ACC on Model 00) pin. This function is primarily intended to
allow faster manufacturing throughput at the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock
Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the
pin to reduce the time required for program operations. The system would use a two-cycle pro-
gram command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/
ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH
for operations other than accelerated programming, or device damage may result. In addition,
相關PDF資料 |
PDF描述 |
|---|---|
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI043 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29CD016G0JDEI004 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD016G0JDEI007 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD032J1JFAI122 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29AL032D70BAI000 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 32Mbit 4M x 8bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI030 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI032 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA T/R |
| S29AL032D70BFI000 | 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29AL032D70BFI030 | 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。