- 您現在的位置：買賣IC網 > PDF目錄192295 > S29AL032D90TFI042 (Spansion Inc.) 32 Megabit CMOS 3.0 Volt-only Flash Memory PDF資料下載
參數資料
| 型號： | S29AL032D90TFI042 |
| 廠商： | Spansion Inc. |
| 英文描述： | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| 中文描述： | 32兆位的CMOS 3.0伏只閃存 |
| 文件頁數： | 29/69頁 |
| 文件大小： | 1970K |
| 代理商： | S29AL032D90TFI042 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
June 13, 2005 S29AL032D_00_A3
S29AL032D
33
Ad vance
Info rmat i o n
the Embedded Program algorithm. The system is not required to provide further controls or tim-
ings. The device automatically generates the program pulses and verifies the programmed cell
margin. Table 17 on page 38 shows the address and data requirements for the byte program
command sequence.
When the Embedded Program algorithm is complete, the device then returns to reading array
data and addresses are no longer latched. The system can determine the status of the program
operation by using DQ7, DQ6, or RY/BY#. See Write Operation Status on page 39 for information
on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note
that a hardware reset immediately terminates the programming operation. The Byte Program
command sequence should be reinitiated once the device has reset to reading array data, to en-
sure data integrity.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be pro-
grammed from a 0 back to a 1. Attempting to do so may halt the operation and set DQ5 to 1,
or cause the Data# Polling algorithm to indicate the operation was successful. However, a suc-
ceeding read will show that the data is still 0. Only erase operations can convert a 0 to a 1.
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program bytes or words to the device faster than
using the standard program command sequence. The unlock bypass command sequence is initi-
ated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock
bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock by-
pass program command sequence is all that is required to program in this mode. The first cycle
in this sequence contains the unlock bypass program command, A0h; the second cycle contains
the program address and data. Additional data is programmed in the same manner. This mode
dispenses with the initial two unlock cycles required in the standard program command sequence,
resulting in faster total programming time. Table 17 on page 38 shows the requirements for the
command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset com-
mands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock
bypass reset command sequence. The first cycle must contain the data 90h; the second cycle the
data 00h. Addresses are don’t care for both cycles. The device then returns to reading array data.
Figure 4, on page 34 illustrates the algorithm for the program operation. See the Erase/Program
Operations on page 54 for parameters, and to Figure 18, on page 55 for timing diagrams.
相關PDF資料 |
PDF描述 |
|---|---|
| S29AL032D90TFI043 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29CD016G0JDEI004 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD016G0JDEI007 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD032J1JFAI122 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| S29CD032J1MFAN120 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29AS008J70BFI030 | 功能描述:閃存 8Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29AS008J70BFI032 | 制造商:Spansion 功能描述:8 MEG CMOS 1.8 VOLT-ONLY BOOT SECTOR FLASH MEMORY - Trays |
| S29AS008J70BFI042 | 制造商:Spansion 功能描述:8 MEG CMOS 1.8 VOLT-ONLY BOOT SECTOR FLASH MEMORY - Trays |
| S29AS008J70TFI030 | 功能描述:閃存 8Mb 1.8V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29AS008J70TFI040 | 功能描述:閃存 8Mb 1.8V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。