欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: S29CL016J0MFAM100
廠商: SPANSION LLC
元件分類: PROM
英文描述: 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80
封裝: 13 X 11 MM, 1 MM PITCH, FORTIFIED, BGA-80
文件頁數: 22/78頁
文件大小: 1825K
代理商: S29CL016J0MFAM100
September 27, 2006 S29CD-J_CL-J_00_B1
S29CD-J & S29CL-J Flash Family
27
Pr el im i n a r y
Table 8.5 describes the Configuration Register settings.
8.5
Autoselect
The autoselect mode provides manufacturer and device identification, and sector protection ver-
ification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for
programming equipment to automatically match a device to be programmed with its correspond-
ing programming algorithm. However, the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Ad-
dress pins A6, A1, and A0 must be as shown in Table 8.7. In addition, when verifying sector pro-
tection, the sector address must appear on the appropriate highest order address bits. Table 8.7
Table 8.5 Configuration Register
Configuration Register
CR15 = Read Mode (RM)
0 = Synchronous Burst Reads Enabled
1 = Asynchronous Reads Enabled (Default)
CR14 = Reserved for Future Enhancements
These bits are reserved for future use. Set these bits to 0.
CR13–CR10 = Initial Burst Access Delay Configuration (IAD3-IAD0)
0000 = 2 CLK cycle initial burst access delay
0001 = 3 CLK cycle initial burst access delay
0010 = 4 CLK cycle initial burst access delay
0011 = 5 CLK cycle initial burst access delay
0100 = 6 CLK cycle initial burst access delay
0101 = 7 CLK cycle initial burst access delay
0110 = 8 CLK cycle initial burst access delay
0111 = 9 CLK cycle initial burst access delay—Default
CR9 = Data Output Configuration (DOC)
0 = Hold Data for 1-CLK cycle—Default
1 = Reserved
CR8 = IND/WAIT# Configuration (WC)
0 = IND/WAIT# Asserted During Delay—Default
1 = IND/WAIT# Asserted One Data Cycle Before Delay
CR7 = Burst Sequence (BS)
0 = Reserved
1 = Linear Burst Order—Default
CR6 = Clock Configuration (CC)
0 = Reserved
1 = Burst Starts and Data Output on Rising Clock Edge—Default
CR5–CR3 = Reserved For Future Enhancements (R)
These bits are reserved for future use. Set these bits to 0.
CR2–CR0 = Burst Length (BL2–BL0)
000 = Reserved, burst accesses disabled (asynchronous reads only)
001 = 64 bit (8-byte) Burst Data Transfer - x32 Linear
010 = 128 bit (16-byte) Burst Data Transfer - x32 Linear
011 = 256 bit (32-byte) Burst Data Transfer - x32 Linear (device default)
100 = Reserved, burst accesses disabled (asynchronous reads only)
101 = Reserved, burst accesses disabled (asynchronous reads only)
110 = Reserved, burst accesses disabled (asynchronous reads only)
Table 8.6 Configuration Register After Device Reset
CR15
CR14
CR13
CR12
CR11
CR10
CR9
CR8
RM
Reserve
IAD3
IAD2
IAD1
IAD0
DOC
Reserve
1
0011
1
0
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
BS
CC
Reserve
BL2
BL1
BL0
1
1000
1
0
相關PDF資料
PDF描述
S29CL016J0PFFM102 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80
S29CL016J1JFFM112 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80
S29CD032J1JFAN110 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80
S29CD032J1JFFN020 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80
S29CL032J0RFAI113 1M X 32 FLASH 3.3V PROM, 48 ns, PBGA80
相關代理商/技術參數
參數描述
S29CL016J0MQFM030 制造商:Spansion 功能描述:
S29CL016J0MQFM030P 制造商:Spansion 功能描述:32M (4MX8/2MX16) 3V REG, MIRRORBIT, TOP, FBGA48, IND - Trays
S29CL016J1JFAI020 制造商:Spansion 功能描述:16 - Tape and Reel
S29CL032J0MFAI030 制造商:Spansion 功能描述:32MBIT FLASH - Trays
S29CL032J0PQFM010 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:32MBIT FLASH - Tape and Reel
主站蜘蛛池模板: 宁波市| 囊谦县| 阿拉善盟| 辉县市| 四子王旗| 沧州市| 德安县| 安溪县| 宝山区| 黄山市| 潼南县| 唐河县| 张家川| 承德县| 田阳县| 海林市| 理塘县| 柘城县| 南投县| 永修县| 山阳县| 鲁甸县| 南通市| 濮阳县| 冀州市| 阜南县| 田林县| 巫山县| 安乡县| 梨树县| 扎赉特旗| 北票市| 明溪县| 石台县| 乐亭县| 乌拉特后旗| 平利县| 江门市| 巴彦县| 平定县| 铜山县|