- 您現在的位置：買賣IC網 > PDF目錄24552 > 051-053-0000 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 051-053-0000 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 5/42頁 |
| 文件大小： | 489K |
| 代理商： | 051-053-0000 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Dimensions are shown in mm (inch)
Dimensions subject to change
114
RF Coaxial Connectors
Assembly Instructions
AI-128 & AI-663
SSMB/SSMC Straight Connectors, Crimp Type for Braided Cable
HEAT
SHRINKABLE
TUBING
CRIMP
FERRULE
REAR BODY
REAR
INSULATOR
CONTACT
FRONT
BODY
1. Slide heat shrinkable tubing and ferrule on to cable.
2. Trim cable to dimensions shown.
Assembly Instruction No.
B
C
D
AI-663
6,86 (.270)
2,29 (.090)
10,41 (.410)
AI-128 - For center conductors
X 0,51 (.020)
6,76 (.266)
2,29 (.090)
9,53 (.375)
AI-128 - For all other conductor sizes
7,54 (.297)
3,05 (.120)
10,31 (.406)
3. Slide rear body over dielectric and under the braid until braid is flush with flange.
N.B. When using cable with inflexible jackets it is permissible to make two 3,00 (.118) long
longitudinal slits in the outer jacket.
4. Slide ferrule over exposed braid up to hex. flange.
5. Crimp using ITT Cannon Crimp Tool and suitable die set (see table). Ensure ferrule is held close to
hex. flange.
6. Slide heat shrinkable tubing over crimp and heat shrink into place using hot air gun. Air
temperature should be approximately 125
°C.
7. Trim dielectric flush with surface ‘A’ on body using a sharp knife. Take care not to nick center
conductor.
8. Trim center conductor as shown.
9. Tin center conductor (do not allow solder to touch end of body or dielectric).
10. Place a small solder preform made from 0,26 - 0,31 (.010 - .012) dia. (28 swg) multi-core solder
in rear of contact.
11. Place rear insulator over center conductor. When insulator has counterbore, the contact fits into
the counterbore.
12. Assemble contact onto center conductor, heat to make solder connection. Do not allow solder to
protrude outside spill hole.
13. Solder should be visible at inspection hole, if excess solder runs from inspection hole, remove
with sharp blade taking care not to damage plating.
14. Screw on the front body and tighten to a torque of 0.14 Nm (20 in. ozs.).
Only common cable retention features are shown in detail - various body configurations can
apply.
Cable Type
Cable Code
Die Size
RG196/U
3196
2,67 (.105)
RG316/U
3188
3,25 (.128)
RD316
3875
3,84 (.151)
相關PDF資料 |
PDF描述 |
|---|---|
| 66.6660MHZIQXO-70B | CRYSTAL OSCILLATOR, CLOCK, 66.666 MHz, HCMOS/TTL OUTPUT |
| 53.1250MHZIQXO-71B | CRYSTAL OSCILLATOR, CLOCK, 53.125 MHz, HCMOS OUTPUT |
| 50.0MHZIQXO-71IB | CRYSTAL OSCILLATOR, CLOCK, 50 MHz, HCMOS OUTPUT |
| 53.1250MHZIQXO-70B | CRYSTAL OSCILLATOR, CLOCK, 53.125 MHz, HCMOS/TTL OUTPUT |
| 53.1250MHZIQXO-70IB | CRYSTAL OSCILLATOR, CLOCK, 53.125 MHz, HCMOS/TTL OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 051-053-0349 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 051-0534-300 | 功能描述:燈透鏡 LARGE PANEL IND RoHS:否 制造商:Dialight 產品:Lens Caps 燈類型:Incandescent 燈大小:T-1 3/4 封裝:Bulk |
| 051-053-9029 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 051-053-9601229 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 051-053-9602229 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
發布緊急采購，3分鐘左右您將得到回復。