欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: 051-428-3188
廠商: ITT Corporation
英文描述: RF Coaxial Connectors
中文描述: 射頻同軸連接器
文件頁數: 26/42頁
文件大小: 489K
代理商: 051-428-3188
Dimensions are shown in mm (inch)
Dimensions subject to change
133
Assy Insts
RF Coaxial Connectors
Assembly Instructions
BBAI-1119
SMZ Straight Connectors, Crimp Contact, for Braided Cable
Cable
Die Size
BT2001
4,52 (.178)
BT2002
5,18 (.204)
BT2003
6,81 (.268)
BT3002
4,52 (.178)
RG59B/U
6,48 (.255)
RG179B/U
3,25 (.128)
RG187A/U
3,25 (.128)
TZC75024
4,52 (.178)
FERRULE
REAR BODY ASSEMBLY
CONTACT
(REAR PORTION)
FRONT
INSULATOR
(PLUG ONLY)
1. Check that the center contact is a free fit in the front insulator and that you have all the connector
parts. The termination technique and cable preparation dimensions for the sockets are the same.
2. Strip the cable to the dimensions shown taking care not to damage the braid, dielectric or inner
conductor. Slip ferrule over cable.
3. Slide the connector body over the cable so that the rear body goes between the dielectric and the
braid. Gently twisting and rocking the connector body to spread the braid will help. Care must be
taken to ensure that no strands of braid are trapped under the body.
4. Slide the crimp ferrule forward over the braid until it butts up against the backnut. Crimp using
ITT Cannon crimp tool fitted with suitable die set (see table).
5. Trim the center conductor so that 3,50 (.138) protrudes from the face of the rear insulator. Position
the crimp type center pin over the end of the center conductor. The wire should be visible through
the inspection hole when positioned for crimping.
6. A separate crimping tool will be needed to crimp the center pin. A suitable tool being the
ITT Cannon crimp tool T4519.
7. The center pin together with the connector body is inserted into the locator of the crimp tool, taking
care that the center pin does not fall off in the process! As the connector body is inserted, the spring
loaded plunger positions the center pin against the rear insulator. With the connector firmly pushed
into the locator, crimp the center pin. (Ensure assembly is resting on bottom of locator.)
8. Withdraw the connector. Assemble the front and rear bodies. If a free fit front insulator is utilised
ensure that it is positioned the correct way round. Finally tighten the two body sections using
torque wrenches ITT Cannon part numbers T0854/M8/E and T0854/13/E, to a torque of 0,98 -
1,06 Nm (140 - 150 in. ozs.).
BRAID OPENED
FOR REAR BODY
相關PDF資料
PDF描述
9164001M2A QUAD LINE RECEIVER, CQCC20
9164001MEA QUAD LINE RECEIVER, CDIP16
9164001MFA QUAD LINE RECEIVER, CDFP16
9166C 1M X 32 FAST PAGE DRAM MODULE, 60 ns, SMA72
9169AM-70LF 80.18 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO32
相關代理商/技術參數
參數描述
051-428-3196 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors
051-428-3702-220 制造商:ITT Interconnect Solutions 功能描述:ALLIED IAW#030-00447-0002 - Bulk
051-428-3875 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors
051-428-9399 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors
051429-000 制造商:. 功能描述:
主站蜘蛛池模板: 德惠市| 湾仔区| 海阳市| 夹江县| 博客| 安西县| 乳源| 岑巩县| 南安市| 农安县| 岳阳市| 开鲁县| 麟游县| 长兴县| 石渠县| 昌邑市| 凌云县| 子洲县| 江阴市| 邓州市| 镇安县| 泾阳县| 阿克苏市| 阿拉善盟| 广德县| 岑巩县| 桑植县| 宜都市| 广汉市| 会昌县| 镇江市| 达日县| 华池县| 荣昌县| 济南市| 乌兰浩特市| 康平县| 丘北县| 进贤县| 科技| 昭觉县|