- 您現在的位置：買賣IC網 > PDF目錄106300 > 1021RE-42TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | 1021RE-42TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 2/17頁 |
| 文件大小： | 107K |
| 代理商： | 1021RE-42TE13 |
10
CAT1021, CAT1022, CAT1023
Preliminary Information
Doc. No. 3009, Rev. E
ACKNOWLEDGE
After a successful data transfer, each receiving device
is required to generate an acknowledge. The
acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8 bits
of data.
All devices respond with an acknowledge after receiving
a START condition and its slave address. If the device
has been selected along with a write operation, it
responds with an acknowledge after receiving each 8-
bit byte.
When a device begins a READ mode it transmits 8 bits
of data, releases the SDA line and monitors the line for
an acknowledge. Once it receives this acknowledge, the
device will continue to transmit data. If no acknowledge
is sent by the Master, the device terminates data
transmission and waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information (with
the R/
W bit set to zero) to the Slave device. After the Slave
generates an acknowledge, the Master sends a 8-bit
address that is to be written into the address pointers of
the device. After receiving another acknowledge from the
Slave, the Master device transmits the data to be written
into the addressed memory location. The device
acknowledges once more and the Master generates the
STOP condition. At this time, the device begins an
internal programming cycle to non-volatile memory. While
the cycle is in progress, the device will not respond to any
request from the Master device.
Figure 7. Slave Address Bits
CAT
Default Configuration
1
010
0
R/W
START BIT
SDA
STOP BIT
SCL
Figure 5. Start/Stop Timing
ACKNOWLEDGE
1
START
SCL FROM
MASTER
89
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 6. Acknowledge Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 1021SI-30TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 1025ZD4I-45TE13 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO8 |
| 110IMY15-15-15-8 | 2-OUTPUT 16.8 W DC-DC REG PWR SUPPLY MODULE |
| 12ICR1-1515-S | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 110IMX7-05-05-7M | 2-OUTPUT 7 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1021S | 功能描述:脈沖變壓器 PULSE TRANS RoHS:否 制造商:Murata Power Solutions 安裝風格:SMD/SMT 匝數比:1:1:1 電感:1890 uH 次級線圈電阻: 電壓時間 - Et: 長度:12.7 mm 寬度:9.52 mm 高度:6.35 mm |
| 1022 | 功能描述:電池座、電池扣和電池接頭 "AAA" DUAL SMT battery holder RoHS:否 制造商:Eagle Plastic Devices 產品:Battery Snaps 電池組電池大小:9 V 電池數量:1 端接類型:Snaps 顏色:Black 材料:Polyvinyl Chloride (PVC) 安裝風格:Snap-In |
| 1022.0101 | 功能描述:基本/快動開關 SNAP ACTION RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| 1022.09.565-003 | 制造商:Walter schrickel 功能描述:Bulk |
| 1022.09.780-005 | 制造商:Walter schrickel 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。