- 您現在的位置：買賣IC網 > PDF目錄106302 > 1022RD4E-45TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 PDF資料下載
參數資料
| 型號： | 1022RD4E-45TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, MSOP FOOTPRINT, TDFN-8 |
| 文件頁數： | 17/17頁 |
| 文件大小： | 107K |
| 代理商： | 1022RD4E-45TE13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁
9
Preliminary Information
CAT1021, CAT1022, CAT1023
Doc No. 3009, Rev. E
EMBEDDED EEPROM OPERATION
The CAT1021/22/23 feature a 2kbit embedded serial
EEPROM that supports the I2C Bus data transmission
protocol. This Inter-Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter
and any device receiving data to be a receiver. The
transfer is controlled by the Master device which
generates the serial clock and all START and STOP
conditions for bus access. Both the Master device and
Slave device can operate as either transmitter or receiver,
but the Master device controls which mode is activated.
I2C Bus Protocol
The features of the I2C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT1021/22/23 monitor
the SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant
bits of the 8-bit slave address are programmable in metal
and the default is 1010.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this bit
is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT1021/22/23 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT1021/22/23 then perform a Read or Write operation
depending on the R/
W bit.
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
ACK
8TH BIT
BYTE n
SCL
SDA
Figure 4. Write Cycle Timing
tHIGH
SCL
SDA IN
SDA OUT
tLOW
tF
tLOW
tR
tBUF
tSU:STO
tSU:DAT
tHD:DAT
tHD:STA
tSU:STA
tAA
tDH
Figure 3. Bus Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 1022RD4A-42TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 15ICR6-15-SB | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| 15IYR1-15-15-N | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 15IZR1-12-N | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 110IMY15-24-24-9RI | 2-OUTPUT 16.8 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1022R-IB25 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DURCHZUGSLESER IR 25POL SUB D BUCHSE |
| 1022R-RB25 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DURCHZUGSLESER ROTLICHT25POL SUBD BUCHSE |
| 1022TR | 功能描述:電池座、電池扣和電池接頭 AAA DUAL SMT battery holder RoHS:否 制造商:Eagle Plastic Devices 產品:Battery Snaps 電池組電池大小:9 V 電池?cái)?shù)量:1 端接類型:Snaps 顏色:Black 材料:Polyvinyl Chloride (PVC) 安裝風格:Snap-In |
| 1022W-IB9F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DURCHZUGSLESER TTL AUSGANG IR LICHT |
| 1022W-RB9F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DURCHZUGSLESER TTL AUSGANG ROTLICHT |
發布緊急采購，3分鐘左右您將得到回復。