- 您現在的位置：買賣IC網 > PDF目錄106304 > 1025PE-42TE13 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 PDF資料下載
參數資料
| 型號： | 1025PE-42TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 5/17頁 |
| 文件大小： | 105K |
| 代理商： | 1025PE-42TE13 |
13
Preliminary Information
CAT1024, CAT1025
Doc No. 3008, Rev. G
Immediate/Current Address Read
The CAT1024 and CAT1025 address counter contains
the address of the last byte accessed, incremented by
one. In other words, if the last READ or WRITE access
was to address N, the READ immediately following
would access data from address N+1. For all devices,
N=E=255. The counter will wrap around to Zero and
continue to clock out valid data for the 2K devices. After
the CAT1024 and CAT1025 receives its slave address
information (with the R/
W bit set to one), it issues an
acknowledge, then transmits the 8-bit byte requested.
The master device does not send an acknowledge, but
will generate a STOP condition.
Selective/Random Read
Selective/Random READ operations allow the Master
device to select at random any memory location for a
READ operation. The Master device first performs a
‘dummy’ write operation by sending the START condition,
slave address and byte addresses of the location it
wishes to read. After the CAT1024 and CAT1025
acknowledges, the Master device sends the START
condition and the slave address again, this time with the
R/
W bit set to one. The CAT1024 and CAT1025 then
responds with its acknowledge and sends the 8-bit byte
requested. The master device does not send an
acknowledge but will generate a STOP condition.
Sequential Read
The Sequential READ operation can be initiated by
either the Immediate Address READ or Selective READ
operations. After the CAT1024 and CAT1025 sends the
inital 8-bit byte requested, the Master will responds with
an acknowledge which tells the device it requires more
data. The CAT1024 and CAT1025 will continue to output
an 8-bit byte for each acknowledge, thus sending the
STOP condition.
The data being transmitted from the CAT1024 and
CAT1025 is sent sequentially with the data from address
N followed by data from address N+1. The READ
operation address counter increments all of the CAT1024
and CAT1025 address bits so that the entire memory
array can be read during one operation.
SLAVE
ADDRESS
S
A
C
K
N
O
A
C
K
S
T
O
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
BYTE
ADDRESS (n)
S
A
C
K
DATA n
SLAVE
ADDRESS
A
C
K
S
T
A
R
T
Figure 11. Selective Read Timing
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+x
DATA n
A
C
K
A
C
K
DATA n+1
A
C
K
S
T
O
P
N
O
A
C
K
DATA n+2
A
C
K
P
SLAVE
ADDRESS
Figure 12. Sequential Read Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 1021ZD4E-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 1025LI-45TE13 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 12IWR1-05-05-NT | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 12FR15S | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 12H1301-7RD2 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1025PG2C | 制造商:HB 制造商全稱:HB Electronic Components 功能描述:LED SPECIFICATION |
| 1025PWC | 制造商:HB 制造商全稱:HB Electronic Components 功能描述:LED |
| 1025R_10 | 制造商:API 制造商全稱:API Delevan 功能描述:Molded Unshielded RF Coils |
| 1025R-00F | 功能描述:固定電感器 .15uH 1% .1ohm Molded Unshield Coil RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| 1025R-00G | 功能描述:固定電感器 .15uH 2% .1ohm Molded Unshield Coil RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。