- 您現在的位置：買賣IC網 > PDF目錄106299 > 1026RA-25TE13 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | 1026RA-25TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | MSOP-8 |
| 文件頁數： | 2/17頁 |
| 文件大小： | 108K |
| 代理商： | 1026RA-25TE13 |
10
CAT1026, CAT1027
Preliminary Information
Doc. No. 3010, Rev. E
ACKNOWLEDGE
After a successful data transfer, each receiving device
is required to generate an acknowledge. The
acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8 bits
of data.
The CAT1026 and CAT1027 respond with an
acknowledge after receiving a START condition and its
slave address. If the device has been selected along
with a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT1026 and CAT1027 begin a READ mode
it transmits 8 bits of data, releases the SDA line and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT1026 and CAT1027 will
continue to transmit data. If no acknowledge is sent by
the Master, the device terminates data transmission and
waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information (with
the R/
W bit set to zero) to the Slave device. After the Slave
generates an acknowledge, the Master sends a 8-bit
address that is to be written into the address pointers of
the device. After receiving another acknowledge from the
Slave, the Master device transmits the data to be written
into the addressed memory location. The CAT1026 and
CAT1027 acknowledge once more and the Master
generates the STOP condition. At this time, the device
begins an internal programming cycle to non-volatile
memory. While the cycle is in progress, the device will not
respond to any request from the Master device.
Figure 8. Slave Address Bits
CAT
Default Configuration
1
010
0
R/W
START BIT
SDA
STOP BIT
SCL
Figure 6. Start/Stop Timing
ACKNOWLEDGE
1
START
SCL FROM
MASTER
89
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 7. Acknowledge Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 1022SA-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 12IWR1-05-NS | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 12IYR1-05-15-N | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 15IZR1-0505-S | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 15IZR1-05-N | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1026-S | 功能描述:折皺器 SPRNG ACT SIDE PLIER RoHS:否 制造商:Hirose Connector 類型: 描述/功能:Cable and Shield Crimper |
| 10-26UD-AU-16 | 功能描述:0.11 X 0.26 AU 16--10-26UD-AU-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:金 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-BD-16 | 功能描述:0.10 X 0.26 BD 16--10-26UD-BD-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:沒有鍍層 鍍層 - 厚度:- 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-NI-16 | 功能描述:0.10 X 0.26 NI 16--10-26UD-NI-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:鎳 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-SN-16 | 功能描述:0.10 X 0.26 SN 16--10-26UD-SN-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:錫 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
發布緊急采購，3分鐘左右您將得到回復。