Pads the snap serves as the ground point. A secon" />

欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: 14246
廠商: Desco
文件頁數: 6/8頁
文件大?。?/td> 0K
描述: GND MICA FLUSH MNT INS W/14260
標準包裝: 1
附件類型: 接地點
適用于相關產品: 靜電耗散薄片
TB-2091 Page 6 of 8
performing this test on Micastat
Pads the snap serves as
the ground point.
A second type of test is RTT (Resistance, Point to Point).
Here you measure the resistance from one 5 lb. electrode
to another 5 lb. electrode; see electrode test positions A, B,
C, and D in RTT test diagram, Figure 13. This is the test
that is more typically used in the laboratory to determine
Micastat
compliance with electrical specifications.
Both test procedures are outlined in this Technical Bulletin
using the Desco Surface Resistance Test Kit Item No.
19780.
Figure 11. Electrode positions on surface of pad, RTG test.
Resistance To Ground (RTG):
1. Locate the five pound electrode positions, as described
below, to be used on the Micastat
surface in relationship
to the installed ground bolt (or snap on the Micastat
Pad). Use the relative positions shown above.
A -
At least 2" from any surface edge and 3"
from the ground bolt.
B, C & D - The farthest corners from the ground bolt and
2" from any surface edge.
E -
The geometric center of the surface.
2. Disconnect the surface to be tested from its normal
ground connection.
3. Connect one black lead to the meter and the other end
of this lead to the 5 lb. electrode.
Figure 12. Proper connection of leads.
4. Connect the other black lead to the meter and the
groundable point on the mat.
5. Place the electrode at position A on the mat (see the
RTG diagram) and set the meter selector switch to 100V.
6. Push on On/Off button, for the 15 second electrification
period and then record the reading in ohms.
7. Release the On/Off button. Move the electrode to each
of the other four positions on the surface and repeat the
test.
8. Average the results of the five readings to obtain an
average measurement of the resistance of surface to
ground.
Resistance Point to Point (RTT):
Figure 13. Electrode positions on surface of pad, RTT test.
1. Locate the four pair of electrode positions to be used
approximately as shown in the RTT test diagram above.
Position electrodes at least 10 inches apart and not less
than two inches from any edge.
2. Disconnect the surface to be tested from its normal
ground connection.
3. Connect one end of the black lead to the meter connect
the other end of this lead to either one of the electrodes.
It does not matter which lead is connected to which
weighted electrode.
DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178 Fax (909) 627-7449
DESCO EAST - One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Fax (781) 575-0172 Web Site: http://www.desco.com
2009 DESCO INDUSTRIES, INC.
Employee Owned
相關PDF資料
PDF描述
OSTHB062180 CONN TERM BLOCK 6POS 7.5MM
OSTHA064150 CONN TERM BLOCK 6POS 10MM
1-87499-2 CONN HOUSING 6POS .100 SINGLE
OSTHA076050 CONN TERM BLOCK 7POS 7.5MM
OSTHE084040 CONN TERM BLOCK 8POS 2.5MM
相關代理商/技術參數
參數描述
1424600000 功能描述:CONTACT CS1.6E 22-20GLD .75 I2.5 RoHS:是 類別:連接器,互連式 >> 矩形 - 觸點 系列:- 標準包裝:90,000 系列:* 其它名稱:035021-1301350211-1301350211301
14246-00000-20 功能描述:3M MAXIM GT PROTECTIVE E 制造商:3m 系列:* 零件狀態:在售 標準包裝:1
1424601 功能描述:PWR CBL 5POS M12 SKT-WIRE 1.5M 制造商:phoenix contact 系列:* 零件狀態:在售 標準包裝:1
1424601-1 功能描述:手工工具 PLATE, COVER RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool
1424602 功能描述:PWR CBL 5POS M12 SKT-WIRE 3M 制造商:phoenix contact 系列:* 零件狀態:在售 標準包裝:1
主站蜘蛛池模板: 敖汉旗| 英吉沙县| 雅安市| 荔浦县| 连云港市| 沙洋县| 桂东县| 侯马市| 屯门区| 寿光市| 迁安市| 彰武县| 榕江县| 福贡县| 桐柏县| 杨浦区| 河池市| 察哈| 大同县| 准格尔旗| 收藏| 宁都县| 永修县| 九寨沟县| 赞皇县| 延吉市| 东台市| 犍为县| 蕉岭县| 开平市| 泸州市| 海林市| 江山市| 大兴区| 黔西| 桂林市| 巴青县| 蓬安县| 北海市| 黄山市| 永丰县|