- 您現在的位置：買賣IC網 > PDF目錄293798 > 3656AG Transformer Coupled ISOLATION AMPLIFIER PDF資料下載
參數資料
| 型號： | 3656AG |
| 元件分類： | 隔離放大器 |
| 英文描述： | Transformer Coupled ISOLATION AMPLIFIER |
| 中文描述： | 變壓器耦合隔離放大器 |
| 文件頁數： | 5/17頁 |
| 文件大小： | 149K |
| 代理商： | 3656AG |
3656
13
FIGURE 8. Bipolar Current Output.
where VO is the output voltage of A3, and VCM is the
common-mode voltage between the inputs L
A and RA and
the input common at pin 3 of the 3656.
This circuit has the added benefit of having higher common-
mode rejection than the circuit in Figure 6 (approximately
10dB improvement).
BIPOLAR CURRENT OUTPUT
The three-port capability of the 3656 can be used to imple-
ment a current output isolation amplifier function—usually
difficult to implement when grounded loads are involved.
The circuit is shown in Figure 8 and the following equations
apply:
G = IOUT/VIN = 1 +
X
IOUT ≤ ±2.5mA
V
1 ≤ ±4V (compliance)
RL ≤ 1.6k
RF + RA = R1 + R2 ≤ 2M
CURRENT OUTPUT—
LARGER UNIPOLAR CURRENTS
A more practical version of the current output function is
shown in Figure 9. If the circuit is powered from a source
greater than 15V as shown, a three-terminal regulator should
R
A
R
F
be used to provide 15V for the pulse generator (pins 19 and
20). The input stage is configured as a unity gain buffer,
although other configurations such as current input could be
used. The circuit uses the isolation feature between the
output stage and the primary power supply to generate the
output current configuration that can work into a grounded
load. Note that the output transistors can only drive positive
current into the load. Bipolar current output would require a
second transistor and dual supply.
ISOLATED 4mA TO 20mA OUTPUT
Figure 10 shows the circuit of an expanded version of the
isolated current output function. It allows any input voltage
range to generate the 4mA to 20mA output excursion and is
also capable of zero suppression. The “span” (gain) is
adjusted by R2 and the “zero” (4mA output for minimum
input) is set by the 200k
pot in the output stage. A three-
terminal 5V reference is used to provide a stable 4mA
operating point. The reference is connected to insert an
adjustable bias between the demodulator output and the
noninverting input of the output stage.
DIFFERENTIAL INPUT
Figure 11 shows the proper connections for differential input
configuration. The 3656 is capable of operating in this input
configuration only for floating loads (i.e., the source VIN
has no connection to the ground reference established at
pin 3). For this configuration the usual 2M
resistor used in
(R
1 + R2) RS
R
2
R
A
D
M
V
IN
+
–
R
C
I/P PWR
+
–
0.47F
–
+
15V
V
L
7
4
6
9
2
10
15
11
13
17
16
12
O/P PWR
Pulse GEN
19
1
3
20
14
R
F
R
L
R
1
R
2
R
S
0.47F
I
OUT
A
1
A
2
相關PDF資料 |
PDF描述 |
|---|---|
| 3656BG | Transformer Coupled ISOLATION AMPLIFIER |
| 3656 | Transformer Coupled ISOLATION AMPLIFIER |
| 380-90-102-00-001000 | SIP2, IC SOCKET |
| 380-40-151-00-001000 | SIP51, IC SOCKET |
| 380-90-122-00-001000 | SIP22, IC SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 3656BG | 功能描述:特殊用途放大器 Transformer Coupled Iso Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| 3656F | 制造商:JT&T Products 功能描述: |
| 3656F1 | 制造商: 功能描述: |
| 3656HG | 功能描述:特殊用途放大器 Transformer Coupled Iso Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| 3656JG | 功能描述:特殊用途放大器 Transformer Coupled Iso Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。