- 您現在的位置：買賣IC網 > PDF目錄68788 > 424/T2C9-1FJA (EVERLIGHT ELECTRONICS CO LTD) T-1 3/4 SINGLE COLOR LED, WHITE, 5 mm PDF資料下載
參數資料
| 型號： | 424/T2C9-1FJA |
| 廠商： | EVERLIGHT ELECTRONICS CO LTD |
| 元件分類： | LED |
| 英文描述： | T-1 3/4 SINGLE COLOR LED, WHITE, 5 mm |
| 封裝： | ROHS COMPLIANT, PLASTIC PACKAGE-2 |
| 文件頁數： | 12/12頁 |
| 文件大小： | 230K |
| 代理商： | 424/T2C9-1FJA |
Technical Data Sheet
424/T2C9-1FJA
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev
1
Page: 9 of 12
Device Number DLE-0000685
Established date: 12-30-2008
Established by: Ruby Lin
Notes
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the
epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage
the LED’s characteristics or it may break the LEDs.
Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures
may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead
position of the LED. If the LEDs are mounted with stress at the leads, it causes
deterioration of the epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from
Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or
more, they can be stored for a year in a sealed container with a nitrogen atmosphere and
moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity
environments where condensation can occur.
3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm
from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is
recommended.
Recommended soldering conditions:
Hand Soldering
DIP Soldering
Temp. at tip of
iron
300
Max.
℃
(30W
Max.)
Preheat temp.
100
Max.
℃
(60 sec
Max.)
Soldering time
3 sec Max.
Bath temp. & time
260 Max., 5 sec Max
Distance
3mm Min.(From
solder joint to
epoxy bulb)
Distance
3mm Min. (From
solder joint to epoxy
bulb)
相關PDF資料 |
PDF描述 |
|---|---|
| 45-21/KK2C-S30308BACB41/2T | DUAL COLOR LED, WARM WHITE |
| 45-21/KK2C-S4040AC4CB41/2T | DUAL COLOR LED, WARM WHITE |
| 5.5URD33TTF2000 | VERY FAST BLOW ELECTRIC FUSE, 2000A, 550VAC, 200000A (IR), INLINE/HOLDER |
| 5URD32D08A1250 | VERY FAST BLOW ELECTRIC FUSE, 1250A, 500VAC, 200000A (IR), INLINE/HOLDER |
| 5URD33TTF2250 | VERY FAST BLOW ELECTRIC FUSE, 2250A, 500VAC, 200000A (IR), INLINE/HOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4-24X7/16FLT PH ST CAD | 制造商:TAPPING SCREWS 功能描述: |
| 425 | 功能描述:去焊 SUPRWIK .075in WIDTH GREEN 5FT LENGTH RoHS:否 制造商:Chip Quik 產品:Desoldering Tools 類型: |
| 4-25 | 制造商:Olympic Controls Corporation 功能描述: |
| 425 (1 X 60) | 制造商:3M Electronic Products Division 功能描述:Aluminum Foil Tape 1 in x 60 yd (Boxed) |
| 425 (2 X 60) | 制造商:3M Electronic Products Division 功能描述:Aluminum Foil Tape 2 in x 60 yd (Boxed) |
發布緊急采購，3分鐘左右您將得到回復。