- 您現在的位置：買賣IC網 > PDF目錄56694 > 4N46#500 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER PDF資料下載
參數資料
| 型號： | 4N46#500 |
| 元件分類： | 光電耦合器 |
| 英文描述： | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 封裝： | SURFACE MOUNT PACKAGE-6 |
| 文件頁數： | 6/9頁 |
| 文件大小： | 141K |
| 代理商： | 4N46#500 |
6
VCC = 5 V
Figure 5. Current Transfer Ratio vs.
Input Current.
Figure 6. Propagation Delay vs.
Forward Current.
Figure 7. Propagation Delay vs.
Temperature.
Notes:
1. Derate linearly above 50
°C free-air
temperature at a rate of 0.4 mA/
°C.
2. Derate linearly above 50
°C free-air
temperature at a rate of 0.7 mW/
°C.
3. Derate linearly above 25
°C free-air
temperature at a rate of 0.8 mA/
°C.
4. Derate linearly above 25
°C free-air
temperature at a rate of 1.5 mW/
°C.
5. DC CURRENT TRANSFER RATIO is
defined as the ratio of output
collector current, IO, to the forward
LED input current, IF, times 100%.
6. Pin 6 Open.
Package Characteristics
For 0
°C ≤ T
A ≤ 70°C, unless otherwise specified. All typicals at TA = 25°C.
Parameter
Symbol
Min.
Typ.
Max. Units
Test Conditions
Fig.
Notes
Input-Output Momentary
VISO
3750
V rms
RH
≤ 50%, t = 1 min,
7, 10
Withstand Voltage*
TA = 25°C
Resistance, Input-Output
RI-O
1012
VI-O = 500 Vdc
7
Capacitance, Input-Output
CI-O
0.6
pF
f = 1 MHz
7
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification, or Agilent Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
maximum tolerable (negative)
dVcm/dt on the trailing edge of the
common mode pulse signal, Vcm, to
assure that the output will remain in
a Logic Low state (i.e., VO < 2.5 V).
10. In accordance with UL 1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥ 4500 V rms for 1 second (leakage
detection current limit, II-O ≤ 5 A).
7. Device considered a two-terminal
device: Pins 1, 2, 3 shorted together
and Pins 4, 5, and 6 shorted together.
8. Use of a resistor between pin 4 and 6
will decrease gain and delay time.
(See Figures 11, 12, and 13.)
9. Common mode transient immunity in
Logic High level is the maximum
tolerable (positive) dVcm/dt on the
leading edge of the common mode
pulse, VCM, to assure that the output
will remain in a Logic High state (i.e.,
VO > 2.5 V). Common mode transient
immunity in Logic Low level is the
Figure 2. Input Diode Forward
Current vs. Forward Voltage.
Figure 3. Typical DC Transfer
Characteristics.
Figure 4. Output Current vs. Input
Current.
相關PDF資料 |
PDF描述 |
|---|---|
| 4N46 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 4N46 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 4N46 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 4N45#300 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 4N45#500 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4N46-500E | 功能描述:高速光耦合器 3750 Vrms 20mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| 4N46-560E | 功能描述:高速光耦合器 3750 Vrms 20mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| 4N46HP | 制造商:HP 功能描述:4N46 S9G3A |
| 4N47 | 功能描述:晶體管輸出光電耦合器 Optocoupled Isolator RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
| 4N47A | 功能描述:晶體管輸出光電耦合器 Optocoupled Isolator RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。