
2
FN6491.0
May 2, 2007
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . 12.6V
Slewrate between VS+ and VS-. . . . . . . . . . . . . . . . . . . . . . . . 1V/s
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 20mA
I into VIN+, VIN-, Enable Pins . . . . . . . . . . . . . . . . . . . . . . . . . ±4mA
Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
Flat Pack Package (Notes
1, 2) . . . . . .
165
60
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . -55°C to +125°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144mW
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1.
θ
JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. For
θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
VS+ = +5V, VS- = -5V, RF = 392Ω for AV = 1, RF = 250Ω for AV = 2, RL = 150Ω, TA = +25°C
Unless Otherwise Specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
AV = +1
1400
MHz
AV = +2
800
MHz
BW1
0.1dB Bandwidth
AV = +2
100
MHz
SR
Slew Rate
VO = -2.5V to +2.5V, AV = +2
6000
V/s
tS
0.1% Settling Time
VOUT = -2.5V to +2.5V, AV = -1
8
ns
eN
Input Voltage Noise
1.7
nV/
√Hz
iN-
IN- Input Current Noise
19
pA/
√Hz
iN+
IN+ Input Current Noise
50
pA/
√Hz
dG
Differential Gain Error (Note
3)AV = +2
0.01
%
dP
Differential Phase Error (Note
3)AV = +2
0.03
°
INPUT CHARACTERISTICS
CIN
Input Capacitance
1.5
pF
ENABLE (5962-0625601QHC ONLY)
tEN
Enable Time
170
ns
tDIS
Disable Time
1.25
s
NOTE:
3. Standard NTSC test, AC signal amplitude = 286mV, f = 3.58MHz.
5962-0625601QHC, 5962-0625602QHC