- 您現在的位置：買賣IC網 > PDF目錄56721 > 5962-0721303QDX 4 CHANNEL, VIDEO AMPLIFIER, CDFP14 PDF資料下載
參數資料
| 型號： | 5962-0721303QDX |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 4 CHANNEL, VIDEO AMPLIFIER, CDFP14 |
| 封裝： | CERAMIC, DFP-14 |
| 文件頁數： | 5/6頁 |
| 文件大小： | 133K |
| 代理商： | 5962-0721303QDX |
5
FN6478.0
March 30, 2007
5962-0721301QHC, 5962-0721302QHC, 5962-0721302QDC
Ceramic Metal Seal Flatpack Packages (Flatpack)
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the lim-
its of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass
overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness. The maximum lim-
its of lead dimensions b and c or M shall be measured at the cen-
troid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric mate-
rials shall be molded to the bottom of the package to cover the
leads.
8. Dimension Q shall be measured at the point of exit (beyond the
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when sol-
der dip lead finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
-D-
-C-
0.004
H A - B
M
D
S
-A-
-B-
0.036
H A - B
M
D
S
e
E
A
Q
L
A
E1
SEATING AND
L
E2
E3
BASE PLANE
-H-
b
C
S1
M
c1
b1
(c)
(b)
SECTION A-A
BASE
LEAD FINISH
METAL
PIN NO. 1
ID AREA
A
M
D
K10.A MIL-STD-1835 CDFP3-F10 (F-4A, CONFIGURATION B)
10 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
INCHES
MILLIMETERS
NOTES
MIN
MAX
MIN
MAX
A
0.045
0.115
1.14
2.92
-
b
0.015
0.022
0.38
0.56
-
b1
0.015
0.019
0.38
0.48
-
c
0.004
0.009
0.10
0.23
-
c1
0.004
0.006
0.10
0.15
-
D
-
0.290
-
7.37
3
E
0.240
0.260
6.10
6.60
-
E1
-0.280
-7.11
3
E2
0.125
-
3.18
-
E3
0.030
-
0.76
-
7
e
0.050 BSC
1.27 BSC
-
k
0.008
0.015
0.20
0.38
2
L
0.250
0.370
6.35
9.40
-
Q
0.026
0.045
0.66
1.14
8
S1
0.005
-
0.13
-
6
M
-
0.0015
-
0.04
-
N10
10
-
Rev. 0 3/07
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-0822601KXC | DUAL 16-CHANNEL, SGL ENDED MULTIPLEXER, CQFP96 |
| 5962-0822601KXC | DUAL 16-CHANNEL, SGL ENDED MULTIPLEXER, CQFP96 |
| 5962-0822601KXC | DUAL 16-CHANNEL, SGL ENDED MULTIPLEXER, CQFP96 |
| 5962-0920201KXC | 64-CHANNEL, SGL ENDED MULTIPLEXER, CQFP96 |
| 5962-0920301KXC | HEX 16-CHANNEL, SGL ENDED MULTIPLEXER, CQFP96 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-0721303QYC | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500MHz Rail-to-Rail Amplifiers |
| 5962-0721901VHA | 制造商:Texas Instruments 功能描述:OP Amp Single Volt Fdbk ±2.5V/5V 10-Pin CFPAK Tube 制造商:Texas Instruments 功能描述:OP AMP SGL VOLT FDBK 2.5V/5V 10CFPAK - Bulk |
| 5962-0722201VFA | 制造商:TI 制造商全稱:Texas Instruments 功能描述:RAD-TOLERANT CLASS V, WIDEBAND, FULLY DIFFERENTIAL AMPLIFIER |
| 5962-0722301VFA | 制造商:Texas Instruments 功能描述:SP Amp DIFF AMP Single ±2.5V/5V 16-Pin CFPAK Tube 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:MIL SPEC TI IC PART |
| 5962-0722401QXB | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Rad-Hard 32 bit SPARC V8 Processor |
發布緊急采購，3分鐘左右您將得到回復。