- 您現在的位置：買賣IC網 > PDF目錄68795 > 5962-8962902LX (ANALOG DEVICES INC) SPECIALTY ANALOG CIRCUIT, CDIP24 PDF資料下載
參數資料
| 型號： | 5962-8962902LX |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, CDIP24 |
| 封裝： | CERDIP-24 |
| 文件頁數： | 19/21頁 |
| 文件大小： | 485K |
| 代理商： | 5962-8962902LX |
AD7569/AD7669
–7–
REV. B
PIN FUNCTION DESCRIPTION
(Applies to the AD7569 and AD7669 unless otherwise stated.)
Pin
Mnemonic
Description
AGNDDAC
Analog Ground for the DAC(s). Separate
ground return paths are provided for the
DAC(s) and ADC to minimize crosstalk.
VOUT
Output Voltage. VOUT is the buffered output
(VOUTA, VOUTB) voltage from the AD7569 DAC. VOUTA and
VOUTB are the buffered DAC output voltages
from the AD7669. Four different output volt-
age ranges can be achieved (see Table I).
VSS
Negative Supply Voltage (–5 V for dual sup-
ply or 0 V for single supply). This pin is also
used with the RANGE pin to select the differ-
ent input/output ranges and changes the data
format from binary (VSS = 0 V) to 2s comple-
ment (VSS = –5 V) (see Table I).
RANGE
Range Selection Input. This is used with the
VSS input to select the different ranges as per
Table I. The range selected applies to both
the analog input voltage of the ADC and the
output voltage from the DAC(s).
RESET
Reset Input (Active Low). This is an asyn-
chronous system reset that clears the DAC
register(s) to all 0s and clears the INT line of
the ADC (i.e., makes the ADC ready for new
conversion). In unipolar operation, this input
sets the output voltage to 0 V; in bipolar
operation, it sets the output to negative full
scale.
DB7
Data Bit 7. Most Significant Bit (MSB).
DB6–DB2
Data Bit 6 to Data Bit 2.
DGND
Digital Ground.
DB1
Data Bit 1.
DB0
Data Bit 0. Least Significant Bit (LSB).
WR
Write Input (Edge triggered). This is used in
conjunction with CS to write data into the
AD7569 DAC register. It is used in conjunc-
tion with CS and A/B to write data into the
selected DAC register of the AD7669. Data is
transferred on the rising edge of WR.
Pin
Mnemonic
Description
CS
Chip Select Input (Active Low). The device is
selected when this input is active.
RD
READ Input (Active Low). This input must
be active to access data from the part. In the
Mode 2 interface, RD going low starts con-
version. It is used in conjunction with the CS
input (see Digital Interface Section).
ST
Start Conversion (Edge triggered). This is
used when precise sampling is required. The
falling edge of ST starts conversion and drives
BUSY
low. The ST signal is not gated with
CS
.
BUSY
BUSY Status Output (Active Low). When
this pin is active, the ADC is performing a
conversion. The input signal is held prior to
the falling edge of BUSY (see Digital Inter-
face Section).
INT
INTERRUPT Output (Active Low). INT go-
ing low indicates that the conversion is com-
plete. INT goes high on the rising edge of CS
or RD and is also set high by a low pulse on
RESET
(see Digital Interface Section).
A
/B (AD7669
DAC Select Input. This input selects which
Only)
DAC register data is written to under control
of CS and WR. With this input low, data is
written to the DACA register; with this input
high, data is written to the DACB register.
CLK
A TTL compatible clock signal may be used
to determine the ADC conversion time. Inter-
nal clock operation is achieved by connecting
a resistor and capacitor to ground.
AGNDADC
Analog Ground for the ADC.
VIN
Analog Input. Various input ranges can be se-
lected (see Table I).
VDD
Positive Supply Voltage (+5 V).
Table I. Input/Output Ranges
Input/Output
DB0–DB7
Range
VSS
Voltage Range
Data Format
0
0 V
0 V to +1.25 V
Binary
1
0 V
0 V to +2.5 V
Binary
0
–5 V
±1.25 V
2s Complement
1
–5 V
±2.5 V
2s Complement
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-8963401CA | QUAD OP-AMP, 2500 uV OFFSET-MAX, 34 MHz BAND WIDTH, CDIP14 |
| 5962-8963401CX | QUAD OP-AMP, 2500 uV OFFSET-MAX, 34 MHz BAND WIDTH, CDIP14 |
| 5962-89635012X | OP-AMP, 3000 uV OFFSET-MAX, 10 MHz BAND WIDTH, CQCC20 |
| 5962-8963501PX | OP-AMP, 3000 uV OFFSET-MAX, 10 MHz BAND WIDTH, CDIP8 |
| 5962-8964301XC | OP-AMP, 10000 uV OFFSET-MAX, 40 MHz BAND WIDTH, MBCY12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-8963001EA | 制造商:National Semiconductor Corporation 功能描述:Dual Receiver RS-232/RS-422/RS-423 16-Pin CDIP Rail 制造商:National Semiconductor 功能描述:Dual Receiver RS-232/RS-422/RS-423 16-Pin CDIP Rail |
| 5962-8963101PA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 5962-8963201PA | 制造商:Rochester Electronics LLC 功能描述:SMD HA7-5112 DUAL LOW NOISE OP AMP 8 LD CDIP - Bulk |
| 5962-89635012A | 制造商:Intersil Corporation 功能描述:OP AMP SGL GP 15V 20CLCC - Rail/Tube |
| 5962-8963501PA | 制造商:Intersil Corporation 功能描述:SMD VERSIO HA7-5101/883 NOT DUAL MARKED - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。