- 您現在的位置：買賣IC網 > PDF目錄56739 > 5962-9462902HYC (MS KENNEDY CORP) 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | 5962-9462902HYC |
| 廠商： | MS KENNEDY CORP |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-8 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 259K |
| 代理商： | 5962-9462902HYC |
APPLICATION NOTES
POWER SUPPLIES
The output voltage of the DHC2800S may be adjusted from
90% to 110% of nominal value by the use of a 50K
potenti-
ometer as shown. Adjustment beyond this range is possible
however certain characteristics of the converter such as but
not limited to input voltage range, efficiency, ripple and tem-
perature performance will change. Characterization by the user
is recommended in such applications.
Adjust/comp (pin 3) may be driven by external circuitry refer-
enced to pin 2 (-output) if desired.
Grounding pin 3 causes
voltage to increase (25% typically) while driving pin 3 above
1.3V causes output voltage to decrease. Pin 3 may be driven
through 10K
or more if connection of the comp function is
also required.
The comp function of pin 3 allows capacitive loads as large
as 1000F to be accommodated on the DHC2805S without
loss of stability. This feature may be utilized by connecting a
10nF capacitor between pins 3 and 1. This is generally recom-
mended when low ESR load capacitances of 100F or greater
are used.
Rev. D 12/03
5
SHUTDOWN PLUS
Pin 5 is used for remote shutdown, output fault detection,
and/or setting the input voltage point at which the converter
will turn on as shown in the typical application diagram. No
connection to pin 5 is necessary for normal operation of the
converter. Pin 5 is referenced to the -input (pin 7).
Shutdown may be implemented by simply connecting pin 5
to an open collector logic output or switch rated at 2.5mA,
25Vdc or higher.
Input voltage turn on point is programmed with a single resis-
tor from pin 5 to 7. An input turn on/off hysteresis (typically
3.5% of Vin) will be observed. This should be considered when
making or verifying set point adjustment.
The value of the
setpoint resistor may be determined by the following:
R=
(±10% accuracy at 25°C)
Set point temperature coefficient is typically +400ppm/°C.
Output fault monitoring is accomplished by observing pin 5
with a high impedance monitoring circuit. Pin 5 voltage drops
from over 10V to below 1V when a load fault causes the con-
verters fault protection circuitry to activate. It will remain low
for at least 100mS and return high.
If the load fault is still
present pin 5 will return low and the cycle will repeat. A resis-
tor >400K
from pin 5 to 7 provides pull down for pin 5 if
there is no input setpoint programming resistor already in place.
21010
ETO-9.5
LOAD FAULT RESPONSE
The DHC2800S series of dc-dc converters share load fault
philosophies.
Load fault conditions include short-circuit and
severe overload conditions. The DHC2800S converter series
responds to load faults by turning off all power conversion cir-
cuits for 250mS and then attempting to restart for 10mS (typi-
cal). The net "on" duty factor during a fault is very low result-
ing in low converter dissipation and immunity from overheating
at 125°C.
Current beyond rated can flow into the load at
startup time. This allows the converter to bring up capacitive
and other difficult load types more reliably than competing con-
verters.
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-9309301HXX | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9309001HXX | 2-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9308901HXX | 2-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9309201HXX | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9309401HXX | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-9463101HXA | 制造商:International Rectifier 功能描述:DC/DC CONVERTER, CLASS H - Rail/Tube |
| 5962-9463201MPA | 功能描述:電荷泵 RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| 5962-9463301MLA | 功能描述:數模轉換器- DAC IC MONO 16-BIT DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| 5962-9464901HXA | 制造商:International Rectifier 功能描述:DC/DC CONVERTER, CLASS H - Rail/Tube |
| 59629466401MEA | 制造商:TI 功能描述:CD4046BF3A |
發布緊急采購，3分鐘左右您將得到回復。