- 您現在的位置：買賣IC網 > PDF目錄56742 > 5962-9463102HYA (MS KENNEDY CORP) 1-OUTPUT 5.4 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | 5962-9463102HYA |
| 廠商： | MS KENNEDY CORP |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 5.4 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-8 |
| 文件頁數： | 5/9頁 |
| 文件大小： | 423K |
| 代理商： | 5962-9463102HYA |
APPLICATION NOTES
POWER SUPPLIES
The output voltage of the DAC2812S and DAC2815S may
be adjusted from 90% to 110% of nominal value by the use of
a 150K
potentiometer as shown. Adjustment beyond this
range is possible however certain characteristics of the con-
verter such as but not limited to input voltage range, efficiency,
ripple and temperature performance will change. Characteriza-
tion by the user is recommended in such applications.
Adjust/comp (pin 4) may be driven by external circuitry refer-
enced to pin 2 (-output) if desired.
Grounding pin 4 causes
voltage to increase (25% typically) while driving pin 4 above
1.3V causes output voltage to decrease. Pin 4 may be driven
negative without damage, however the resultant increase in
converter output voltage should be considered. Pin 4 may be
driven through 10K
or more if connection of the comp func-
tion is also required.
The comp function of pin 4 allows load transient response to
be tailored to suit specific application requirements. This fea-
ture may be utilized by connecting a 10 or less nF capacitor
between pins 4 and 1.
Note: The DAC2812S and DAC2815S use pin 4 while the
DHC2803S and DHC2805S use pin 3.
Rev. C 7/04
5
SHUTDOWN PLUS
Pin 5 is used for remote shutdown, output fault detection,
and/or setting the input voltage point at which the converter
will turn on as shown in the typical application diagram. No
connection to pin 5 is necessary for normal operation of the
converter. Pin 5 is referenced to the pin 7 (-input).
Shutdown may be implemented by simply connecting pin 5
to an open collector logic output or switch rated at 2.5mA,
25Vdc or higher.
Input voltage turn on point is programmed with a single resis-
tor from pin 5 to 7. An input turn on/off hysteresis (typically
3.5% of Vin) will be observed. This should be considered when
making or verifying set point adjustment.
The value of the
setpoint resistor may be determined by the following:
R=
(±10% accuracy at 25°C)
Set point temperature coefficient is typically +400ppm/°C.
Output fault monitoring is accomplished by observing pin 5
with a high impedance monitoring circuit. Pin 5 voltage drops
from over 10V to below 1V when a load fault causes the con-
verters fault protection circuitry to activate. It will remain low
for at least 100mS and return high.
If the load fault is still
present pin 5 will return low and the cycle will repeat. A resis-
tor >400K
from pin 5 to 7 provides pull down for pin 5 if
there is no input setpoint programming resistor already in place.
21010
ETO-9.5
LOAD FAULT RESPONSE
The MSK families of DC-DC converters share load fault phi-
losophies. Load fault conditions include short-circuit and se-
vere overload conditions. The DAC2800S converter series re-
sponds to load faults by turning off all power conversion cir-
cuits for 250mS and then attempting to restart for 10mS (typi-
cal). The net "on" duty factor during a fault is very low result-
ing in low converter dissipation and immunity from overheating
at 125°C.
Current beyond rated can flow into the load at
startup time. This allows the converter to bring up capacitive
and other difficult load types more reliably than competing con-
verters.
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-9463001HXA | 1-OUTPUT 5.4 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9309303HUC | 1-OUTPUT 5.4 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9463702MXC | 1-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, QFP68 |
| 5962-9463701MXX | 1-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, QFP68 |
| 5962-9463702MXX | 1-CH 10-BIT FLASH METHOD ADC, PARALLEL ACCESS, QFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-9463201MPA | 功能描述:電荷泵 RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| 5962-9463301MLA | 功能描述:數模轉換器- DAC IC MONO 16-BIT DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| 5962-9464901HXA | 制造商:International Rectifier 功能描述:DC/DC CONVERTER, CLASS H - Rail/Tube |
| 59629466401MEA | 制造商:TI 功能描述:CD4046BF3A |
| 5962-9466401MEA | 制造商:Texas Instruments 功能描述:PLL Single 0.3MHz to 2.4MHz 16-Pin CDIP Tube 制造商:Texas Instruments 功能描述:CD4046BF3A - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。