- 您現在的位置：買賣IC網 > PDF目錄56744 > 5962F9563003VXC (INTERSIL CORP) 16-CHANNEL, SGL ENDED MULTIPLEXER, CDIP28 PDF資料下載
參數資料
| 型號： | 5962F9563003VXC |
| 廠商： | INTERSIL CORP |
| 元件分類： | 多路復用及模擬開關 |
| 英文描述： | 16-CHANNEL, SGL ENDED MULTIPLEXER, CDIP28 |
| 封裝： | CERAMIC, SIDE BRAZED, DIP-28 |
| 文件頁數： | 7/7頁 |
| 文件大小： | 214K |
| 代理商： | 5962F9563003VXC |
HS-1840ARH, HS-1840BRH
7
FN4355.3
September 14, 2010
Ceramic Metal Seal Flatpack Packages (Flatpack)
NOTES:
1. Index area: A notch or a pin one identification mark shall be located
adjacent to pin one and shall be located within the shaded area
shown. The manufacturer’s identification shall not be used as a pin
one identification mark. Alternately, a tab (dimension k) may be
used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the limits
of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass over-
run.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension M
applies to lead plating and finish thickness. The maximum limits of
lead dimensions b and c or M shall be measured at the centroid of
the finished lead surfaces, when solder dip or tin plate lead finish is
applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric materi-
als shall be molded to the bottom of the package to cover the leads.
8. Dimension Q shall be measured at the point of exit (beyond the me-
niscus) of the lead from the body. Dimension Q minimum shall be
reduced by 0.0015 inch (0.038mm) maximum when solder dip lead
finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
-D-
-C-
0.004
H A - B
M
D
S
-A-
-B-
0.036
H A - B
M
D
S
e
E
A
Q
L
D
A
E1
SEATING AND
L
E2
E3
BASE PLANE
-H-
b
C
S1
M
c1
b1
(c)
(b)
SECTION A-A
BASE
LEAD FINISH
METAL
PIN NO. 1
ID AREA
A
M
K28.A MIL-STD-1835 CDFP3-F28 (F-11A, CONFIGURATION B)
28 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
INCHES
MILLIMETERS
NOTES
MIN
MAX
MIN
MAX
A
0.045
0.115
1.14
2.92
-
b
0.015
0.022
0.38
0.56
-
b1
0.015
0.019
0.38
0.48
-
c
0.004
0.009
0.10
0.23
-
c1
0.004
0.006
0.10
0.15
-
D
-
0.740
-
18.80
3
E
0.460
0.520
11.68
13.21
-
E1
-
0.550
-
13.97
3
E2
0.180
-
4.57
-
E3
0.030
-
0.76
-
7
e
0.050 BSC
1.27 BSC
-
k
0.008
0.015
0.20
0.38
2
L
0.250
0.370
6.35
9.40
-
Q
0.026
0.045
0.66
1.14
8
S1
0.00
-
0.00
-
6
M
-
0.0015
-
0.04
-
N28
28
-
Rev. 0 5/18/94
相關PDF資料 |
PDF描述 |
|---|---|
| 5962F9563003VYC | 16-CHANNEL, SGL ENDED MULTIPLEXER, CDFP28 |
| 5962F9563003QYC | 16-CHANNEL, SGL ENDED MULTIPLEXER, CDFP28 |
| 5962F9581304QCC | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, CDIP14 |
| 5962F9581305VCC | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, CDIP14 |
| 5962F9581304V9A | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, UUC13 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962F9563101VXC | 制造商:Intersil Corporation 功能描述: |
| 5962F9563201VXC | 制造商:Intersil Corporation 功能描述: |
| 5962F9568901QXC | 制造商:Intersil Corporation 功能描述: |
| 5962F9568901VXC | 制造商:Intersil Corporation 功能描述: |
| 5962F9568902QXC | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。