- 您現在的位置：買賣IC網 > PDF目錄369224 > 6300I (Linear Technology Corporation) 500mA, 200MHz X DSL LINE DRIVER IN 16-LEAD SSOP PACKAGE PDF資料下載
參數資料
| 型號： | 6300I |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 500mA, 200MHz X DSL LINE DRIVER IN 16-LEAD SSOP PACKAGE |
| 中文描述： | 500mA的，200MHz的X的DSL線路驅動器，采用16引線SSOP封裝 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 237K |
| 代理商： | 6300I |
11
LT6300
APPLICATIOU
Heat Sinking Using PCB Metal
Designing a thermal management system is often a trial
and error process as it is never certain how effective it is
until it is manufactured and evaluated. As a general rule,
the more copper area of a PCB used for spreading heat
away from the driver package, the more the operating
junction temperature of the driver will be reduced. The
limit to this approach however is the need for very com-
pact circuit layout to allow more ports to be implemented
on any given size PCB.
To best extract heat from the GN16 package, a generous
area of top layer PCB metal should be connected to the four
corner pins (Pins 1, 8, 9 and 16). These pins are fused to
the leadframe where the LT6300 die is attached. It is
important to note that this heat spreading metal area is
electrically connected to the V
–
supply voltage.
Fortunately xDSL circuit boards use multiple layers of
metal for interconnection of components. Areas of metal
beneath the LT6300 connected together through several
small 13 mil vias can be effective in conducting heat away
from the driver package. The use of inner layer metal can
free up top and bottom layer PCB area for external compo-
nent placement.
When PCB cards containing multiple ports are inserted
into a rack in an enclosed cabinet, it is often necessary to
provide airflow through the cabinet and over the cards.
This is also very effective in reducing the junction-to-
ambient thermal resistance of each line driver. To a limit,
this thermal resistance can be reduced approximately
5
°
C/W for every 100lfpm of laminar airflow.
W
U
U
Layout and Passive Components
With a gain bandwidth product of 200MHz the LT6300
requires attention to detail in order to extract maximum
performance. Use a ground plane, short lead lengths and
a combination of RF-quality supply bypass capacitors (i.e.,
0.1
μ
F). As the primary applications have high drive cur-
rent, use low ESR supply bypass capacitors (1
μ
F to 10
μ
F).
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input can combine with
the input capacitance to form a pole that can cause
frequency peaking. In general, use feedback resistors of
1k or less.
Compensation
The LT6300 is stable in a gain 10 or higher for any supply
and resistive load. It is easily compensated for lower gains
with a single resistor or a resistor plus a capacitor.
Figure8 shows that for inverting gains, a resistor from the
inverting node to AC ground guarantees stability if the
parallel combination of R
C
and R
G
is less than or equal to
R
F
/9. For lowest distortion and DC output offset, a series
capacitor, C
C
, can be used to reduce the noise gain at
lower frequencies. The break frequency produced by R
C
and C
C
should be less than 5MHz to minimize peaking.
Figure 9 shows compensation in the noninverting configu-
ration. The R
C
, C
C
network acts similarly to the inverting
case. The input impedance is not reduced because the
network is bootstrapped. This network can also be placed
between the inverting input and an AC ground.
Figure 8. Compensation for Inverting Gains
R
G
R
C
V
O
V
I
C
C
(OPTIONAL)
–
+
6300
F08
R
F
= –R
F
R
G
V
O
V
I
< 5MHz
1
2
π
R
C
C
C
(R
C
|| R
G
)
≤
R
F
/9
R
C
V
O
V
I
C
C
(OPTIONAL)
+
–
6300
F09
R
F
R
G
= 1 +
R
F
R
G
V
O
V
I
< 5MHz
1
2
π
R
C
C
C
(R
C
|| R
G
)
≤
R
F
/9
Figure 9. Compensation for Noninverting Gains
相關PDF資料 |
PDF描述 |
|---|---|
| 630MMB103JE7TC | METALLIZED POLYESTER FILM CAPACITORS |
| 630MMB103JH7TC | METALLIZED POLYESTER FILM CAPACITORS |
| 630MMB103KE7TC | METALLIZED POLYESTER FILM CAPACITORS |
| 630MMB104JE7TC | METALLIZED POLYESTER FILM CAPACITORS |
| 630MMB104KE7TC | METALLIZED POLYESTER FILM CAPACITORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 6300L | 制造商:3M Electronic Products Division 功能描述:3M 6300L LOW MAINTENANCE RESP LARGE 制造商:3M Electronic Products Division 功能描述:LOW MAINTENANCE RESP LARGE |
| 6300Q | 功能描述:FLOOR FINISH STATIC DISS 1 QT RoHS:否 類別:靜電控制，ESD，無塵室產品 >> 處理劑，清潔劑，擦拭布 系列:- 標準包裝:100 系列:- 處理劑/清潔劑類型:清潔布 使用:電子設備 技術規格:無絨毛，微纖維 數量:100（12" L x 12" W） 包裝:袋 |
| 6300SCG002T | 制造商:LG Corporation 功能描述:LED 135-838265-03 HLC8205-0124 |
| 6300T1 | 功能描述:LED Circuit Board Indicator Single Red Diffused 1.8V 10mA Round with Domed Top, 3mm (T-1), 2.85mm 制造商:visual communications company - vcc 系列:6300T 包裝:* 零件狀態:在售 顏色:紅色 波長 - 峰值:655nm 配置:單一 電流:10mA 毫燭光等級:18mcd 視角:50° 透鏡類型:散射 透鏡樣式/尺寸:圓形，帶圓頂，3mm（T-1），2.85mm 額定電壓:1.8V 安裝類型:* 標準包裝:1 |
| 6300T15 | 功能描述:LED Circuit Board Indicator Single Green, Red Diffused 2.5V Green, 2.5V Red 20mA Round with Domed Top, 3mm (T-1), 2.85mm 制造商:visual communications company - vcc 系列:6300T 包裝:* 零件狀態:在售 顏色:綠色，紅色 波長 - 峰值:565nm 綠色，627nm 紅色 配置:單一 電流:20mA 毫燭光等級:9mcd 綠色，6.7mcd 紅色 視角:50° 透鏡類型:散射 透鏡樣式/尺寸:圓形，帶圓頂，3mm（T-1），2.85mm 額定電壓:2.5V 綠色色，2.5V 紅色色 安裝類型:* 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。