欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: 71M6511-IGT/F
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
封裝: LEAD FREE, LQFP-64
文件頁數: 46/98頁
文件大小: 1278K
代理商: 71M6511-IGT/F
71M6511/71M6511H
Single-Phase Energy Meter IC
DATA SHEET
NOVEMBER 2010
Page: 50 of 98
2005–2010 Teridian Semiconductor Corporation
V2.7
A Maxim Integrated Products Brand
Data Flow
The data flow between CE and MPU is shown in Figure 17. In a typical application, the 32-bit compute engine (CE)
sequentially processes the samples from the voltage inputs on pins IA, VA, and IB, performing calculations to measure active
power (Wh), reactive power (VARh), A
2h, and V2h for four-quadrant metering. These measurements are then accessed by the
MPU, processed further and output using the peripheral devices available to the MPU.
CE
MPU
Pre-
Processor
Post-
Processor
IRQ
Processed
Metering
Data
Pulses
I/O RAM (Configuration RAM)
Samples
Data
Figure 17: MPU/CE Data Flow
CE/MPU Communication
Figure 18 shows the functional relationship between CE and MPU. The CE is controlled by the MPU via shared registers in the
I/O RAM and by registers in the CE DRAM. The CE outputs two interrupt signals to the MPU: CE_BUSY and XFER_BUSY,
which are connected to the MPU interrupt service inputs as external interrupts. CE_BUSY indicates that the CE is actively
processing data. This signal will occur once every multiplexer cycle. XFER_BUSY indicates that the CE is updating data to the
output region of the CE RAM. This will occur whenever the CE has finished generating a sum by completing an accumulation
interval determined by SUM_CYCLES * PRE_SAMPS samples. Interrupts to the MPU occur on the falling edges of the
XFER_BUSY and CE_BUSY signals.
Figure 19 shows the sequence of events between CE and MPU upon reset or power-up. In a typical application, the sequence
of events is as follows:
1)
Upon power-up, the MPU initializes the hardware, including disabling the CE
2)
The MPU loads the code for the CE into the CE PRAM
3)
The MPU loads CE data into the CE DRAM.
4)
The MPU starts the CE by setting the CE_EN bit in the I/O RAM.
5)
The CE then repetitively executes its code, generating results and storing them in the CE DRAM
It is important to note that the length of the accumulation interval, as determined by NACC, the product of SUM_CYCLES and
PRE_SAMPS is not an exact multiple of 1000ms. For example, if SUM_CYCLES = 60, and PRE_SAMPS = 00 (42), the resulting
accumulation interval is:
ms
Hz
f
N
S
ACC
75
.
999
62
.
2520
13
32768
42
60
=
=
τ
This means that accurate time measurements should be based on the RTC, not the accumulation interval.
相關PDF資料
PDF描述
71M6511-IGT 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
71M6511-IGTR 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
71M6511H-IGTR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
71M6511H-IGT/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
71M6511H-IGT 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64
相關代理商/技術參數
參數描述
71M6511-IGTR 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Single-Phase Energy Meter IC
71M6511-IGTR/F 功能描述:計量片上系統 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6511-IGTR/F1 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6512-DB 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 71M6512 Demo Brd
71M6512-IM/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Meter Extended Io
主站蜘蛛池模板: 林西县| 宁强县| 西安市| 绥江县| 双牌县| 呼图壁县| 博乐市| 丹棱县| 互助| 邳州市| 永川市| 班玛县| 中宁县| 思南县| 克什克腾旗| 黄冈市| 涞源县| 松阳县| 南丹县| 高青县| 年辖:市辖区| 河东区| 施秉县| 新化县| 扎兰屯市| 巨鹿县| 腾冲县| 岳西县| 宝丰县| 东乡| 合阳县| 分宜县| 上饶县| 孙吴县| 水城县| 德州市| 丰都县| 白沙| 巴彦县| 渑池县| 乐昌市|