- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6532D-IGT/F (MAXIM INTEGRATED PRODUCTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6532D-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 75/120頁 |
| 文件大小： | 2477K |
| 代理商： | 71M6532D-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Data Sheet 71M6531D/F-71M6532D/F
FDS 6531/6532 005
58
2005-2010 TERIDIAN Semiconductor Corporation
v1.3
can voluntarily enter LCD or SLEEP modes. When system power is restored, the part will automatically
transition from any of the battery modes to MISSION mode, once the PLL has settled.
The MPU will run at 7/8 of the crystal clock rate. This permits the UARTs to be operated at 300 bd. In
this mode, the MPU clock has substantial short-term jitter.
The value of MPU_DIV[2:0] will be remembered (not changed) as the part enters and exits BROWNOUT.
MPU_DIV[2:0] will be ignored during BROWNOUT.
While PLL_OK = 0, the I/O RAM bits ADC_E and CE_E are held in the zero state disabling both the ADC and
the CE. When PLL_OK falls, the CE program counter is cleared immediately and all FIR processing halts.
2.3.2
LCD Mode
In LCD mode, the data contained in the LCD_SEGn[3:0] fields is displayed. Up to four LCD segments,
each connected to pins SEG18 and SEG19, can be made to blink without the involvement of the MPU,
which is disabled in LCD mode. To minimize power, only segments that might be used should be
enabled.
LCD mode can be exited only by system power up, a timeout of the wake-up timer, or a push button.
When the IC exits LCD mode, the MPU can discover the event that caused the exit by reading the interrupt
flags and interpret them as follows:
IE_WAKE = 1 indicates that the wake timer has expired.
IE_PB =1 indicates that the pushbutton input (PB) was activated.
COMPSTAT = 0 indicates that a reset occurred but that main power is not yet available.
If none of the above conditions applies, system power (V3P3SYS) must have been restored
After the transition from LCD mode to MISSION or BROWNOUT mode, the PC will be at 0x0000, the
XRAM is in an undefined state and the I/O RAM is only partially preserved (see the description of I/O RAM
states in Section 4.2). The GP0[7:0] through GP7[7:0] registers are preserved unless RESET goes high.
2.3.3
SLEEP Mode
In SLEEP mode, the battery current is minimized and only the Oscillator and RTC functions are active.
This mode can be exited only by system power-up, a timeout of the wake-up timer, or a push button event.
When the IC exits SLEEP mode, the MPU can discover the event that caused the exit by reading the
interrupt flags and interpret them as follows:
IE_WAKE = 1 indicates that the wake timer has expired.
IE_PB =1 indicates that the pushbutton input (PB) was activated.
COMPSTAT = 0 indicates that a reset occurred but that main power is not yet available.
If none of the above conditions applies, system power (V3P3SYS) must have been restored
After the transition from SLEEP mode to MISSION or BROWNOUT mode the PC will be at 0x0000, the
XRAM is in an undefined state and the I/O RAM is only partially preserved (see the description of I/O RAM
states in Section 4.2). The GP0[7:0] through GP7[7:0] registers are preserved unless RESET goes high.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6531D-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532F-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6532D-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6531D-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532F-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6532D-IGTR/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532D-IGTR/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Energy Meter IC |
| 71M6532F-IGT/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGT/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。