- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6543F-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543F-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 27/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
122
2008–2011 Teridian Semiconductor Corporation
v1.2
5.4.6
CE Front-End Data (Raw Data)
Access to the raw data provided by the AFE is possible by reading CE RAM addresses 0 through A, as
shown in Table 74. In the expression MUXn_SEL[3:0] = x, ‘n’ refers to the multiplexer frame time slot number
and ‘x’ refers to the desired ADC input number or ADC handle (i.e., IADC0 to VADC10, or simply 0 to 10
decimal).
The 71M6543 can support up to eleven sensor inputs, when all the current sensors are configured as
single-ended inputs. If all the current sensor inputs are configured as differential (recommended for
best performance), the number of input sensor channels is reduced to seven (i.e., IADC0-1, IADC2-3,
IADC4-5, IADC6-7, VADC8, VADC9 and VADC10). The MUXn_SEL[3:0] column in Table 74 shows the
MUXn_SEL handles for the various sensor input pins. For example, if differential mode is enabled via
control bit DIFF0_E = 1 (I/O RAM 0x210C[4]), then the IADC0-IADC1 input pins are combined together to
form a single differential input and the corresponding MUXn_SEL handle is 0 (i.e., handle 1 is then unused).
Similarly, the CE RAM location column provides the CE RAM address where the corresponding sample data
is stored. Continuing with the same example, if DIFF0_E = 1, the corresponding CE RAM location where the
samples for the IADC0-IADC1 differential input are stored is CE RAM 0.
The IADC2-3, IADC4-5 and IADC6-7 inputs can be configured as direct-connected sensors (i.e., directly
connected to the 71M6543) or as remote sensors (i.e., using a 71M6xx3 Isolated Sensor). For example, if the
IADC2-3 remote sensor is disabled by RMT2_E = 0 (I/O RAM 0x2007[3]) and differential mode is enabled by
DIFF2_E = 1 (I/O RAM 0x210C[4]), then IADC2-IADC3 form a differential input with a MUXn_SEL handle of 2
(i.e., handle 3 is then unused), and the corresponding samples are stored in CE RAM location 2. If the
remote sensor enable bit RMT2_E = 1, DIFF2_E = x (don’t care), then the MUXn_SEL handle is not required
(i.e., the sensor is not connected to the 71M6543 multiplexer, so MUXn_SEL does not apply), and the
samples corresponding to this remote differential IADC2-IADC3 input are stored in CE RAM location 2
directly by the digital isolation interface (see Figure 2).
The voltage sensor inputs (VADC8, VADC9 and VADC10) are always single-ended inputs and cannot be
configured as remotes, so they do not have any associated configuration bits. VADC8 (VA) has a
MUXn_SEL handle value of 8, and its samples are stored in CE RAM location 8. VADC9 (VB) has a
MUXn_SEL handle value of 9 and its samples are stored in CE RAM location 9. VADC10 (VC) has a
MUXn_SEL handle value of 10 and its samples are stored in CE RAM location 10.
Table 74: CE Raw Data Access Locations
Pin
MUXn_SEL Handle
CE RAM Location
DIFF0_E
0
1
0
1
IADC0
0
IADC1
1
RMT2_E, DIFF2_E
0,0
0,1
1,0
1,1
0,0
0,1
1,0
1,1
IADC2
2
-
2
2*
IADC3
3
RMT4_E, DIFF4_E
0,0
0,1
1,0
1,1
0,0
0,1
1,0
1,1
IADC4
4
-
4
4*
IADC5
5
RMT6_E, DIFF6_E
0,0
0,1
1,0
1,1
0,0
0,1
1,0
1,1
IADC6
6
-
6
6*
IADC7
7
There are no configuration bits for VADC8, 9, 10
VADC8 (VA)
8
VADC9 (VB)
9
VADC10 (VC)
10
*Remote interface data
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543F-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電表IC |
發布緊急采購，3分鐘左右您將得到回復。