參數資料
| 型號： | 73640 |
| 廠商： | Desco |
| 文件頁數： | 3/4頁 |
| 文件大小： | 0K |
| 描述： | COAT LAB W/SNAPS TEAL XSMALL |
| 標準包裝： | 1 |
| 系列： | Statshield® |
| 服裝類型： | 實驗室罩衣，帶按扣 |
| 尺寸： | XSmall |
| 材質： | 聚酯 |
| 顏色： | 青色 |
| 特點： | 袖口帶 4mm 卡扣式插口，胯部帶 4mm 卡釘 |
Installation
Follow the directions below for proper installation and
grounding of the Statshield smock.
1. Put on the smock and fasten all of the snaps on the front
of the smock, making sure that clothing is not exposed
outside of the smock.
2. Throughout use, it is essential that conductive cuff (or the
wristband) be in contact with operator’s skin; the
conductive cuff (or the wristband) should never be
allowed to be pulled up and over shirt sleeve.
3. Install a coil cord to the snap stud located above the left
hand hip pocket. Connect the other end of the coil cord
to a verified ground point or continuous monitor.
Grounding Integrity Testing
For daily testing or continuous monitoring of the grounding
integrity of Statshield smocks and ground cords, we
recommend testing the smock while worn and the use of
a standard wrist strap testers or single-wire workstation
continuous monitors. Panel-to-panel conductivity is essential
so as not to leave portions of the smock as isolated charged
conductors. Panel-to-panel conductivity is easy to test using
our Surface Resistance Meter Kit Item #
19787. Place the
two five-pound electrodes on different panels to test. Unless
properly grounded, the smocks can hold a charge and
become a possible source for discharge to ESD sensitive
items. For additional information, refer to ANSI/ESD S20.20,
ESD TR20.20, ESD TR53 and the Garment Standard,
ANSI/ESD STM2.1. Desco has several testers available
for this purpose. For more information ask for specification
drawings or operating instruction manuals by item number.
TB-2055 Page 3 of 4
2013 DESCO INDUSTRIES INC.
Employee Owned
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
Figure 5. Testing and monitoring of smock and ground
cord assembly
YES!
NO!
Figure 3. Proper installation of smock wearer’s body
Figure 4. Grounding the smock
Figure 6. Testers
NOTE: ANSI/ESD S20.20 RECOMMENDS THAT THE
GROUND COIL CORD SELECTED FOR GROUNDING OF
PERSONNEL CONTAIN A BUILT-IN CURRENT LIMITING
1 MEGOHM RESISTOR.
Heat Sealed Patches
It is possible to heat seal patches to our smocks. The patch
should be small and the smock should be tested before and
after application.
相關PDF資料 |
PDF描述 |
|---|---|
| 0988211061 | NSCC HYB RCPT HSG BLK 6CKT |
| 73639 | COAT LAB W/CUFFS WHITE 6XLARGE |
| 768163273GP | RES ARRAY 27K OHM 8 RES 16-SOIC |
| 73638 | COAT LAB W/CUFFS WHITE 5XLARGE |
| 768163274GP | RES ARRAY 270K OHM 8 RES 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 736-402 | 制造商:WAGO Innovative Connections 功能描述:2 Position 5.08 mm Pin Spacing 28-12 AWG Double Deck PCB Terminal Strip |
| 736-408 | 制造商:WAGO 功能描述:MOD DBL DECK PCB ORANGE |
| 73640A00 | 制造商:Siemens 功能描述: |
| 73641 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Statshield Smocks Grounding, Testing and Maintenance |
| 736-412 | 功能描述:罩類、盒類及殼類產品 Polycarb, Trans Door 9.84x7.87x4.8" RoHS:否 制造商:Bud Industries 產品:Boxes 外部深度:6.35 mm 外部寬度:6.35 mm 外部高度:2.56 mm NEMA 額定值: IP 等級: 材料:Acrylonitrile Butadiene Styrene (ABS) 顏色:Red |
發布緊急采購，3分鐘左右您將得到回復。