參數資料
| 型號： | 73771 |
| 廠商： | Desco |
| 文件頁數： | 3/4頁 |
| 文件大小： | 0K |
| 描述： | JACKET W/CUFFS BLUE 3XLARGE |
| 標準包裝： | 1 |
| 系列： | Statshield® |
| 服裝類型： | 外套，帶袖套 |
| 尺寸： | 3XLarge |
| 材質： | 聚酯 |
| 顏色： | 藍 |
| 特點： | 胯部帶 4mm 卡釘，袖口帶導電織物 |
Installation
Follow the directions below for proper installation and
grounding of the Statshield smock.
1. Put on the smock and fasten all of the snaps on the front
of the smock, making sure that clothing is not exposed
outside of the smock.
2. Throughout use, it is essential that conductive cuff (or the
wristband) be in contact with operator’s skin; the
conductive cuff (or the wristband) should never be
allowed to be pulled up and over shirt sleeve.
3. Install a coil cord to the snap stud located above the left
hand hip pocket. Connect the other end of the coil cord
to a verified ground point or continuous monitor.
Grounding Integrity Testing
For daily testing or continuous monitoring of the grounding
integrity of Statshield smocks and ground cords, we
recommend testing the smock while worn and the use of
a standard wrist strap testers or single-wire workstation
continuous monitors. Panel-to-panel conductivity is essential
so as not to leave portions of the smock as isolated charged
conductors. Panel-to-panel conductivity is easy to test using
our Surface Resistance Meter Kit Item #
19787. Place the
two five-pound electrodes on different panels to test. Unless
properly grounded, the smocks can hold a charge and
become a possible source for discharge to ESD sensitive
items. For additional information, refer to ANSI/ESD S20.20,
ESD TR20.20, ESD TR53 and the Garment Standard,
ANSI/ESD STM2.1. Desco has several testers available
for this purpose. For more information ask for specification
drawings or operating instruction manuals by item number.
TB-2055 Page 3 of 4
2013 DESCO INDUSTRIES INC.
Employee Owned
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
Figure 5. Testing and monitoring of smock and ground
cord assembly
YES!
NO!
Figure 3. Proper installation of smock wearer’s body
Figure 4. Grounding the smock
Figure 6. Testers
NOTE: ANSI/ESD S20.20 RECOMMENDS THAT THE
GROUND COIL CORD SELECTED FOR GROUNDING OF
PERSONNEL CONTAIN A BUILT-IN CURRENT LIMITING
1 MEGOHM RESISTOR.
Heat Sealed Patches
It is possible to heat seal patches to our smocks. The patch
should be small and the smock should be tested before and
after application.
相關PDF資料 |
PDF描述 |
|---|---|
| ED555/4DS | TERMINAL BLOCK 3.5MM 4POS PCB |
| 73855 | JACKET W/CUFFS TEAL 2XLARGE |
| OSTTE080104 | TERMINAL BLOCK 3.5MM 8POS PCB |
| 73654 | COAT LAB W/CUFFS TEAL XLARGE |
| TC164-JR-071K8L | RES ARRAY 1.8K OHM 4 RES 1206 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73-771-001 | 功能描述:線性和開關式電源 DS1800/2000 Test Brd RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| 73771-0100 | 功能描述:硬公制連接器 HDM BP Stacking Mo dule 30 Sau 72Ckt RoHS:否 制造商:TE Connectivity / AMP 系列:Z-Pack 產品類型:Receptacles 排數:5 位置/觸點數量:110 安裝角:Right 端接類型:Pin 外殼材料:Polyester 觸點材料:Phosphor Bronze 觸點電鍍:Gold 類型: |
| 73-7710-6 | 制造商:AIM Cambridge Connectivity Solutions 功能描述: |
| 73771-1100 | 功能描述:板對板與夾層連接器 144CKT HDM B/P STACK ING M 737711100 RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
| 73771-1101 | 功能描述:板對板與夾層連接器 HDM BP Stkg Mod PF 3 PF 30 SAu GF 144Ckt RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
發布緊急采購，3分鐘左右您將得到回復。