- 您現在的位置：買賣IC網 > PDF目錄68812 > 73M1903-IVTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | 73M1903-IVTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | ROHS COMPLIANT, MO-153AC, TSSOP-20 |
| 文件頁數： | 2/47頁 |
| 文件大小： | 541K |
| 代理商： | 73M1903-IVTR/F |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
73M1903 Data Sheet
DS_1903_032
10
Rev. 2.1
2.1
GPIO
The 73M1903 modem AFE device provides 8 user defined I/O pins. Each pin is programmed separately
as either an input or an output by a bit in a direction register. If the bit in the direction register is set high,
the corresponding pin is an input whose value is read from the GPIO data register. If it is low, the pin will
be treated as an output whose value is set by the GPIO data register.
To avoid unwanted current contention and consumption in the system from the GPIO port before the
GPIO is configured after a reset, the GPIO port I/Os are initialized to a high impedance state. The input
structures are protected from floating inputs, and no output levels are driven by any of the GPIO pins.
The GPIO pins are configured as inputs or outputs when the host controller (or DSP) writes to the GPIO
direction register. The GPIO direction and data registers are initialized to all ones (FFh) upon reset.
2.1.1
GPIO Data (GPIO): Address 02h
Reset State FFh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
GPIO7
GPIO6
GPIO5
GPIO4
GPIO3
GPIO2
GPIO1
GPIO0
Bits in this register will be asserted on the GPIO(7:0) pins if the corresponding direction register bit is a 0.
Reading this address will return data reflecting the values of pins GPIO(7:0).
2.1.2
GPIO Direction (DIR): Address 03h
Reset State FFh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DIR7
DIR6
DIR5
DIR4
DIR3
DIR2
DIR1
DIR0
This register is used to designate the GPIO pins as either inputs or outputs. If the register bit is low, the
corresponding GPIO pin is programmed as an output. If the register bit is a 1, the corresponding pin will
be treated as an input.
2.2
Analog I/O
Figure 4 shows the block diagram of the analog front end. The analog interface circuit uses differential
transmit and receive signals to and from the external circuitry.
The hybrid driver in the 73M1903 IC is capable of connecting directly, but not limited to, a transformer-
based Direct Access Arrangement (DAA). The hybrid driver is capable of driving the DAA’s line coupling
transformer, which carries an impedance on the primary side that is typically rated at 600
Ω, depending
on the transformer and matching network. The hybrid drivers can also drive high impedance loads
without modification. The class AB behavior of the amplifiers provides load dependent power
consumption.
An on-chip band gap voltage is used to provide an internal voltage reference and bias currents for the
analog receive and transmit channels. The reference derived from the bandgap, nominally 1.25 Volts, is
multiplied to 1.36 Volts and output at the VREF pin. Several voltage references, nominally 1.25 Volts, are
used in the analog circuits. The band gap and reference circuits are disabled after a chip reset since the
ENFE bit is reset to a default state of zero. When ENFE=0, the band gap voltage and the analog bias
currents are disabled. In
this case all of the analog circuits are powered down and draw less than 5 μA of
current.
A clock generator (CKGN) is used to create all of the non-overlapping phase clocks needed for the time
sampled switched-capacitor circuits, ASDM, DAC1, and TLPF. The CKGN input is two times the
analog/digital interface sample rate or 3.072 MHz clock for Fs=8 kHz.
相關PDF資料 |
PDF描述 |
|---|---|
| 73M1903C-IM/F | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 73M1903C-IMR/F | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 73M1903C-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73M1903C-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73S1209F-44IM/F | POWER SUPPLY MANAGEMENT CKT, QCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73M1906B-IM/F | 功能描述:電信線路管理 IC DAA-FXO VOLP System Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| 73M1906B-IM/F1 | 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| 73M1906B-IMR/F | 功能描述:電信線路管理 IC DAA-FXO VOLP System Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| 73M1906B-IMR/F1 | 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| 73M1906B-IVT/F | 功能描述:電信線路管理 IC DAA-FXO VOLP System Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。