- 您現在的位置：買賣IC網 > PDF目錄68812 > 73S8009C-32IM/F (MAXIM INTEGRATED PRODUCTS INC) POWER SUPPLY SUPPORT CKT, QCC32 PDF資料下載
參數資料
| 型號： | 73S8009C-32IM/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC32 |
| 封裝： | ROHS COMPLAINT, QFN-32 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 348K |
| 代理商： | 73S8009C-32IM/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS_8009C_025
73S8009C Data Sheet
Rev. 1.5
21
3.6
Activation and De-activation Sequence
The host controller is fully responsible for the activation sequencing of the smart card signals CLK, RST,
I/O, AUX1 and AUX2. All these signals are held low by the 73S8009C when the card is in the de-
activated state. Upon card activation (the fall of
CMDVCC (#/%)), all the signals are held low by the
73S8009C until RDY goes high. The host should set the signals RSTIN, I/OUC, CLKIN, AUX1UC and
AUX2UC low prior to activating the card and allow RDY to go high before transitioning any of these
signals. In order to initiate activation, the card must be present and
OFF must be high.
CMDVCC5 or CMDVCC3
VCC
I/OUC
I/O
RDY
RSTIN
RST
CLKIN
CLK
Ignored
I/O, AUX1, AUX2, CLK, RST are held LOW until RDY = 1 and CMDVCCx = 0
I/O = I/OUC if RDY=1
CLK=CLKIN if RDY=1
RST = RSTIN if RDY=1
t1
At t1 (50
ξs), if RDY=0 or overcurrent, circuit will de-activate (safety feature)
VCC valid
Figure 5: Activation Sequence
Deactivation is initiated either by the system controller by setting both
CMDVCC (#/%) high, or
automatically in the event of hardware faults or assertion of the OFF_ACK signal. Hardware faults are
over-current, under-voltage, and card extraction during the session. The host can manage the I/O
signals, CLKIN, RSTIN, and
CMDVCC (#/%) to create other de-activation sequences for non-emergency
situations.
The following steps show the deactivation sequence and the timing of the card control signals when the
system controller sets the CMDVCC(x)B high:
1.
RST goes low at the end of time t1.
2.
De-assert CLK at the end of time t2.
3.
I/O goes low at the end of time t3. Exit reception mode.
4.
De-assert internal VCC_ON at the end of time t4. After a delay, VCC is de-asserted.
Note: Since the 73S8009C does not control the waveshape of CLK (it is determined by the input form the
host CLKIN), there is no guarantee that the duty cycle of the last CLK high pulse will conform to duty
cycle requirements during an emergency deactivation.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8009C-32IMR/F | POWER SUPPLY SUPPORT CKT, QCC32 |
| 73S8009R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8009R-IMR | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 73S8009R-IM | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 73S8009R-IMR | SPECIALTY ANALOG CIRCUIT, QCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8009C-32IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8009C-32IMR/F1 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8009C-DB | 功能描述:界面開發工具 73S8009C Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| 73S8009CN | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Combo ISO-7816 and USB Universal Smart Card Interface IC |
| 73S8009CN-32IM/F | 功能描述:輸入/輸出控制器接口集成電路 ISO7816 & USB Unvrsl Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。