- 您現在的位置：買賣IC網 > PDF目錄68812 > 73S8009R-IMR (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC20 PDF資料下載
參數資料
| 型號： | 73S8009R-IMR |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 封裝： | 4 X 4 MM, 0.80 MM HEIGHT, QFN-20 |
| 文件頁數： | 20/23頁 |
| 文件大?。?/td> | 342K |
| 代理商： | 73S8009R-IMR |
73S8009R Data Sheet
DS_8009R_056
6
Rev. 1.3
Table 1 describes the pin functions for the device.
Table 1: 73S8009R Pin Definitions
Pin
Name
Pin
(SO28)
Pin
(QFN20)
Type
Description
Card Interface
I/O
25
15
IO
Card I/O: Data signal to/from card. Includes a pull-up
resistor to VCC.
AUX1
24
NA
IO
AUX1: Auxiliary data signal to/from card. Includes a pull-up
resistor to VCC.
AUX2
23
NA
IO
AUX2: Auxiliary data signal to/from card. Includes a pull-up
resistor to VCC.
RST
21
13
O
Card reset: provides reset signal to card.
CLK
19
11
O
Card clock: provides clock signal to card. The rate of this
clock is determined by the external clock frequency
provided on pin CLKIN.
PRES
26
16
I
Card Presence switch: active high indicates card is present.
Should be tied to GND when not used, but includes a high-
impedance pull-down current source.
PRES
16
10
I
Card Presence switch: active low indicates card is present.
Should be tied to VDD when not used, but includes a high-
impedance pull-up current source.
VCC
22
14
PSO
Card power supply – logically controlled by the sequencer,
output of LDO regulator. Requires an external filter
capacitor to GND.
GND
20
NA
GND
Card ground.
Miscellaneous Inputs and Outputs
CLKIN
11
5
I
Clock source for the card clock.
TEST1
2
19
–
This pin must be tied to GND in typical applications.
TEST2
14
8
–
This pin must be tied to GND in typical applications.
NC
3,17,18
NA
–
Non-connected pin.
Power Supply and Ground
VDD
28
17
System interface supply voltage and supply voltage for
internal circuitry.
VPC
15
9
LDO regulator power supply source.
GND
27
12
GND
Ground.
Microcontroller Interface
CS
1
18
I
When CS = 1, the control and signal pins are configured
normally. When CS is set low,
CMDVCC%, RSTIN, and
CMDVCC# are latched, IOUC, AUX1UC, and AUX2UC are
set to high-impedance pull-up mode and do not pass data
to or from the smart card. Signals RDY and
OFF are
disabled to prevent a low output and the internal pull-up
resistors are disconnected.
OFF
4
20
O
Interrupt signal to the processor. Active low, multi-function
indicating fault conditions and card presence. Open drain
output configuration. It includes an internal 20
kΩ pull-up to
VDD. The pull-up is disabled in PWRDN and CS=0 modes.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8009R-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8009R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8009R-IM | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 73S8009R-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8009R-IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8010C | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Smart Card Interface |
| 73S8010C-DB | 功能描述:界面開發工具 73S8010C Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| 73S8010C-IL/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。