- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010C-IL/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 73S8010C-IL/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | LEAD FREE, SOP-28 |
| 文件頁數： | 6/27頁 |
| 文件大小： | 348K |
| 代理商： | 73S8010C-IL/F |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
73S8010C Data Sheet
DS_8010C_024
14
Rev. 1.5
A power-on-reset (POR) event will reset all of the control and status registers to their default states. A VDD fault
event does not reset these registers, but it will signal an interrupt condition and by the action of the timer that
creates interval “t1,” will not clear the interrupt until VDD is valid for at least the t1 time. The VDD fault can be
considered valid for VDD as low as 1.5 to 1.8 volts. At the lower range of the VDD fault, POR will be asserted.
11 Warm Reset
The 73S8010C automatically asserts a warm reset to the card when instructed through bit 1 of the I
2C Control
register (Warm Reset bit). The warm reset length is automatically defined as 42,000 card clock cycles. The bit
Warm Reset is automatically reset when the card starts answering or when the card is declared mute.
Figure 9: Warm Reset operation
12 I/O Timing
The states of the I/O, AUX1, and AUX2 pins are low after power on reset and they are high when the
activation sequencer turns on the I/O reception state. See Section 8 Activation Sequence for more
details on when the I/O reception is enabled.
The states of I/OUC, AUX1UC, and AUX2UC are high after power on reset. When the control I/O enable
bit (bit 7 of the Control register) is set, the first I/O line on which a falling edge is detected becomes the
input I/O line and the other becomes the output I/O line. When the input I/O line rising edge is detected
then both I/O lines return to their neutral state. The delay between the I/O signals is shown in Figure 10.
Figure 10: I/O Timing
Warm Reset
(bit 1)
RST
t1
t2
t3
IO
t1 > 1.5 s, Warm Reset Starts
t2 = 42000 card clock cycles, End of Warm Reset
t3 = Resets Warm Reset bit 1 when detected ATR or Mute
Delay from I/O to I/OUC:
tIO_HL = 100 ns
tIO_LH = 25 ns
Delay from I/OUC to I/O:
tI/OUC_HL = 100 ns tI/OUC_LH = 25 ns
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010C-IM/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010C-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。