- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010C-IL (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 73S8010C-IL |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | SOP-28 |
| 文件頁數： | 4/27頁 |
| 文件大小： | 367K |
| 代理商： | 73S8010C-IL |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
73S8010C
Smart Card Interface
DATA SHEET
Page: 12 of 27
2005 TERIDIAN Semiconductor Corporation
Rev 1.2
Deactivation Sequence:
Deactivation is initiated either by the system controller by resetting the Start/Stop bit, or automatically in the event
of hardware faults. Hardware faults are over-current, over-temperature, VDD fault, VPC fault, VCC fault, and card
extraction during the session.
The following steps show the deactivation sequence and the timing of the card control signals when the system
controller clears the Start/Stop bit:
-
RST goes low at the end of t1.
-
CLK goes low at the end of t2.
-
I/O goes low at the end of t3. Out of reception mode.
-
Shut down VCC at the end of time t4.
Start/Stop
RST
CLK
IO
VCC
t
1
t
2
t
3
t
4
t1 = > .5s
t2 = > 7.5s
t3 = > 0.5s
t4 = > 0.5s
Figure 7 - De-activation Sequence
Interrupt:
Interrupt is an active low interrupt. It is set low if any of these internal faults are detected:
- VCC fault
- VDD fault
- VPC fault
Or if one of these status bits condition is detected:
-Early ATR
-Mute ATR
-Card insert or card extract
-Protection status from Over-current or Over-heating
In case the interrupt is set low by the detection of these status bits, then the interrupt is set high when these
status bits are read. (READ STATUS DONE)
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010C-IL/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。