- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010R-IL/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 73S8010R-IL/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | LEAD FREE, SOP-28 |
| 文件頁數： | 11/25頁 |
| 文件大小： | 336K |
| 代理商： | 73S8010R-IL/F |
DS_8010R_022
73S8010R Data Sheet
Rev. 1.6
19
3.7
Activation Sequence
After Power on Reset, the signal
INT is low until the V
DD is stable. When VDD has been stable for
approximately 10 ms and the signal
INT is high, the system controller may read the status register to see
if the card is present. If all the status bits are satisfied, the system controller can initiate the activation
sequence by writing a '1' to the Start/Stop bit (bit 0) of the control register.
The following steps and Figure 8 show the activation sequence and the timing of the card control signals
when the system controller initiates the Start/Stop bit (bit 0) of the control register:
1.
Voltage VCC to the card should be valid by the end of t1. If VCC is not valid for any reason, then
the session is aborted.
2.
Turn I/O to reception mode at the end of t1.
3.
CLK is applied to the card at the end of t2.
4.
RST (to the card) is set high at the end of t3.
Start/Stop
VCC
IO
CLK
RST
t
1
t
2
t
3
t1 = 0.510 ms (timing by 1.5MHz internal Oscillator), I/O in reception mode
t2 =1.5
μs, CLK starts
t3 = >42000 card clock cycles, RST set high
Figure 8: Activation Sequence
3.8
Deactivation Sequence
Deactivation is initiated either by the system controller by resetting the Start/Stop bit, or automatically in
the event of hardware faults. Hardware faults are over-current, over-temperature, VDD fault, VPC fault, VCC
fault, and card extraction during the session.
The following steps and Figure 9 show the deactivation sequence and the timing of the card control
signals when the system controller clears the start/stop bit:
1.
RST goes low at the end of t1.
2.
CLK goes low at the end of t2.
3.
I/O goes low at the end of t3. Out of reception mode.
4.
Shut down VCC at the end of time t4.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010R-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010R-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010R-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010R-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。