- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010R-ILR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 73S8010R-ILR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | LEAD FREE, SOP-28 |
| 文件頁數： | 13/25頁 |
| 文件大小： | 336K |
| 代理商： | 73S8010R-ILR/F |
73S8010R Data Sheet
DS_8010R_022
20
Rev. 1.6
Start/Stop
RST
CLK
IO
VCC
t
1
t
2
t
3
t
4
t1 = > .5
μs
t2 = > 7.5
μs
t3 = > 0.5
μs
t4 = > 0.5
μs
Figure 9: Deactivation Sequence
3.9
Interrupt
The Interrupt is an active low interrupt. It is set low if any of the following internal faults are detected:
VCC fault
VDD fault
VPC fault
The interrupt will also be set if one of the following status bit conditions is detected:
Early ATR
Mute ATR
Card insert or card extract
Protection status from Over-current or Over-heating
When the interrupt is set low by the detection of one of the status bits, it is set high when the status bits
are read. (READ STATUS DONE) Figure 10 shows the interrupt operation resulting from the fault or
status bit conditions.
Figure 10: Interrupt operation due to Fault and Status Conditions
A power-on-reset event will reset all of the control and status registers to their default states. A VDD fault
event does not reset these registers, but it will signal an interrupt condition and by the action of the timer
that creates the interval “t1,” not clearing the interrupt until VDD is valid for at least t1. A VDD fault can be
considered valid for VDD as low as 1.5 to 1.8 volts. At the lower range of VDD fault, POR will be asserted.
INT
ANY FAULT
STATUS BITS
READ STATUS DONE
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010R-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010R-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010R-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010R-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010R-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IMR/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。