- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8014RN-ILR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | 73S8014RN-ILR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | LEAD FREE, SOP-20 |
| 文件頁數： | 11/28頁 |
| 文件大小： | 389K |
| 代理商： | 73S8014RN-ILR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
DS_8014RN_014
73S8014RN Data Sheet
Rev. 1.0
19
3.9
Fault Detection and
OFF
There are two different cases that the system controller can monitor the
OFF signal: to query regarding the card
presence outside card sessions, or for fault detection during card sessions.
Outside a card session: In this condition,
CMDVCC is always high, OFF is low if the card is not present, and high
if the card is present. Because it is outside a card session, any fault detection will not act upon the
OFF signal.
No deactivation is required during this time.
During a card session:
CMDVCC is always low, and OFF falls low if the card is extracted or if any fault detection
is detected. At the same time that
OFF is set low, the sequencer starts the deactivation process.
Figure 7 shows the timing diagram for the signals
CMDVCC, PRES, and OFF during a card session and outside
the card session:
e
the card session:
PRES
OFF
CMDVCC
VCC
PRES
OFF
CMDVCC
VCC
outside card session
within card session
OFFis lowby
card extracted
OFFis lowby
anyfault
within card
session
Figure 7: Timing Diagram – Management of the Interrupt Line
OFF
3.10 I/O Circuitry and Timing
The state of the I/O pin is low after power on reset and it goes high when the activation sequencer turns on the
I/O reception state. See the Activation Sequence section for details on when the I/O reception is enabled. The
state of I/OUC is high after power on reset.
Within a card session and when the I/O reception state is turned on, the first I/O line on which a falling edge is
detected becomes the input I/O line and the other becomes the output I/O line. When the input I/O line rising
edge is detected then both I/O lines return to their neutral state.
Note: In certain situations and conditions, the I/O logic can get confused if the host and the card attempt to drive
the IOUC and the I/O signal low at the same time. It should be noted that this is an illegal condition as all card
communication is initiated by the host with a command/response protocol. The next host command should not be
sent until a valid response has been completely received from the card. However, if this condition should occur,
the 8014 may set both the IOUC and the I/O as outputs where they are both driven low at the same time. When
either side drives their respective signal high, then this mode should be released. However, if there is a series
resistance between the host and the 8014, then there may not be enough drive to release this mode. If the series
resistance is greater than about 100 ohms, then this may cause this mode to become locked for the duration of
the card session. If the host detects this condition (IOUC held low for more than one byte time), the card session
must be terminated and restarted.
Figure 8 shows the state diagram of how the I/O and I/OUC lines are managed to become input or output. The
delay between the I/O signals is shown in Figure 9.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8023C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8023C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8023C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8023C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8024C-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8014RT | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Smart Card Interface |
| 73S8014RT-DB | 功能描述:BOARD DEMO 73S8010RT 20-SOIC RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| 73S8014RT-IL/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8014RT-IL/F1 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8014RT-IL/F2 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。