- 您現在的位置：買賣IC網 > PDF目錄97839 > 73S8014RT-IL/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | 73S8014RT-IL/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | ROHS COMPLIANT, SOP-20 |
| 文件頁數： | 1/29頁 |
| 文件大小： | 448K |
| 代理商： | 73S8014RT-IL/F |
當前第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
73S8014RT
Smart Card Interface
Simplifying System Integration
DATA SHEET
December 2008
Rev. 1.0
2008 Teridian Semiconductor Corporation
1
DESCRIPTION
The Teridian 73S8014RT is a single smart card (ICC)
interface circuit. It is derived from the 73S8024RN
industry-standard electrical interface but adds support
for 1.8V smart card applications. The 73S8014RT has
been optimized to match most of the typical Set-Top
Box / A/V Conditional Access applications.
Optimization essentially involved a smaller pin-count
and support for single I/O.
The 73S8014RT has been designed to provide full
electrical compliance with ISO 7816-3, EMV 4.0.
Interfacing with the system controller is done through a
control bus, composed of digital inputs to control the
interface, and one interrupt output to inform the system
controller of the card presence and faults.
The card clock can be generated by an on-chip
oscillator using an external crystal or by connection to
an externally supplied clock signal. In addition, the
clock divider provides divisor values of divide by 1, 2, 4
and 6.
The 73S8014RT incorporates an ISO 7816-3
activation/deactivation sequencer that controls the card
signals. Level-shifters drive the card signals with the
selected card voltage (1.8V, 3V or 5V), coming from an
internal Low Drop-Out (LDO) voltage regulator. This
LDO regulator is powered by a dedicated power supply
input VPC. Digital circuitry is powered separately by a
digital power supply VDD. With its embedded LDO
regulator, the 73S8014RT is a cost-effective solution for
any application where a 5V (typically -5% +10%) power
supply is available.
Emergency card deactivation is initiated upon card
extraction or upon any fault detected by the protection
circuitry. The fault can be a card over-current, VCC
undervoltage or power supply fault (VDD). The card
over-current circuitry is a true current detection function,
as opposed to VCC voltage drop detection, as usually
implemented in non-Teridian 8024 interface ICs.
The VDD voltage fault has a threshold voltage that can
be adjusted with an external resistor network. It allows
automated card deactivation at a customized VDD
voltage threshold value. It can be used, for instance, to
match the system controller operating voltage range.
APPLICATIONS
Set-Top Box Conditional Access and Pay-per-
View
General purpose smart card readers
ADVANTAGES
Same advantages as the Teridian 73S80xxR
family:
Card VCC generated by an LDO regulator
Very low power dissipation (saves up to 1/2W)
Fewer external components are required
Better noise performance
True card over-current detection
Small format 20SO package
FEATURES
Card Interface:
Complies with ISO 7816-3, EMV 4.0
73S801RT device supports 3V / 5V cards up to
65mA and 1.8V up to 40mA
ISO 7816-3 Activation / Deactivation sequencer
Automated deactivation upon hardware fault (i.e.
upon drop on VDD power supply or card
overcurrent)
The VDD voltage supervisor threshold value (fault)
can be externally adjusted
Over-current detection 130mA max
Card CLK clock frequency up to 20MHz
System Controller Interface:
3 Digital inputs control the card activation /
deactivation, card reset and card voltage
2 Digital inputs control the card clock frequency
1 Digital output, interrupt to the system controller,
reports to the host the card presence and faults
Crystal oscillator or host clock, up to 27MHz
Regulator Power Supply:
4.75V to 5.5V (EMV 4.0)
Digital Interfacing: 2.7V to 5.5V
6kV ESD protection on the card interface
Package: SO 20-pin
RoHS compliant (6/6) lead-free package
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8023C-IM/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8023C-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 74HC4046AD/T3 | PLL FREQUENCY SYNTHESIZER, PDSO16 |
| 74HC4067NB | 16-CHANNEL, SGL ENDED MULTIPLEXER, PDIP24 |
| 74HCT4067NB | 16-CHANNEL, SGL ENDED MULTIPLEXER, PDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8014RT-ILR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8014RT-ILR/F1 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8014RT-ILR/F2 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8014RT-ILR/F3 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Smart Card Interface |
發布緊急采購，3分鐘左右您將得到回復。