- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8023C-IMR (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | 73S8023C-IMR |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, QFN-32 |
| 文件頁數： | 25/27頁 |
| 文件大小： | 389K |
| 代理商： | 73S8023C-IMR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁
DS_8023C_019
73S8023C Data Sheet
Rev. 1.5
7
2
System Controller Interface
The CS (chip select) input allows multiple devices to operate in parallel. When CS is high, the system
interface signals operate as described. When CS is taken low, the system interface signals are
latched internally. The pins I/OUC, AUX1UC, and AUX2UC are weakly pulled up and the
OFF signal
is put into a high impedance state.
The CLKSEL signal selects between synchronous and asynchronous operation. When CLKSEL is
low, asynchronous operation is selected. When CLKSEL is high, synchronous operation is selected.
Digital inputs allow direct control of the card interface from the host as follows:
Pin
CMDVCC: When set low, starts an activation sequence if a card is present.
Pin 5V/
#V: Defines the card voltage.
The card I/O and Reset signals have their corresponding controller I/Os to be connected directly to
the host:
Pin RSTIN: controls the card RST signal. When enabled by the sequencer, RST is equal to
RSTIN for both synchronous and asynchronous modes.
Pin I/OUC: data transfer to card I/O contact.
Pins AUX1UC and AUX2UC (auxiliary I/O lines associated to the auxiliary I/Os which are
connected to the C4 and C8 card connector contacts).
Two digital inputs control the card clock frequency division rate: CLKDIV1 and CLKDIV2 define the
card clock frequency from the input clock frequency (crystal or external clock). The division rate is
defined as follows:
CLKDIV2
CLKDIV1
CLK
0
XTAL
0
1
XTAL
1
0
XTAL
1
XTAL
When the division rate is equal to 1 (CLKDIV2 =0 and CLKDIV1 = 1), the duty-cycle of the
card clock depends on the duty-cycle and waveform of the signal applied on the pin XTALIN.
When other division rates are used, the 73S8023C circuitry guarantees a duty-cycle in the
range 45% to 55%, conforming to ISO-7816-3 and EMV 4.1 specifications.
Interrupt output to the host: As long as the card is not activated, the
OFF pin informs the host about
the card presence only (low = no card in the reader). When
CMDVCC is set low (Card activation
sequence requested from the host), a low level on
OFF means a fault has been detected (e.g. card
removedl during a card session, or voltage fault, or thermal / over-current fault) that automatically
initiates a deactivation sequence.
Power Down: The PWRDN pin is a digital input that allows the host controller to put the 73S8023C in
its Power Down state. This pin can only be activated outside of a card session.
The CLKOUT signal is a buffered output of the signal applied to the XTALIN pin whether it is an
external clock source or it is configured as a crystal oscillator. CLKOUT can be used when using
multiple 73S8023C devices to share a single clock signal.
The STROBE input directly drives the smart card CLK signal when operating in synchronous mode.
STROBE is ignored in asynchronous mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8024C-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024C-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024RN-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024RN-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8024RN-32IMR/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8023C-IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F1 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F2 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8023C-IMR/F3 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024C-DB | 功能描述:界面開發工具 73S8024C Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。