欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: 74HCT193DB,112
廠商: NXP Semiconductors
文件頁數: 1/30頁
文件大?。?/td> 0K
描述: IC SYNC 4BIT UP/DWN COUNT 16SSOP
產品培訓模塊: Logic Packages
標準包裝: 78
系列: 74HCT
邏輯類型: 二進制計數器
方向: 上,下
元件數: 1
每個元件的位元數: 4
復位: 異步
計時: 同步
計數速率: 43MHz
觸發器類型: 正邊沿
電源電壓: 4.5 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 16-SSOP
包裝: 管件
其它名稱: 568-2799-5
935189730112
1.
General description
The 74HC193; 74HCT193 is a 4-bit synchronous binary up/down counter. Separate
up/down clocks, CPU and CPD respectively, simplify operation. The outputs change state
synchronously with the LOW-to-HIGH transition of either clock input. If the CPU clock is
pulsed while CPD is held HIGH, the device will count up. If the CPD clock is pulsed while
CPU is held HIGH, the device will count down. Only one clock input can be held HIGH at
any time to guarantee predictable behaviour. The device can be cleared at any time by the
asynchronous master reset input (MR); it may also be loaded in parallel by activating the
asynchronous parallel load input (PL). The terminal count up (TCU) and terminal count
down (TCD) outputs are normally HIGH. When the circuit has reached the maximum
count state of 15, the next HIGH-to-LOW transition of CPU will cause TCU to go LOW.
TCU will stay LOW until CPU goes HIGH again, duplicating the count up clock. Likewise,
the TCD output will go LOW when the circuit is in the zero state and the CPD goes LOW.
The terminal count outputs can be used as the clock input signals to the next higher order
circuit in a multistage counter, since they duplicate the clock waveforms. Multistage
counters will not be fully synchronous, since there is a slight delay time difference added
for each stage that is added. The counter may be preset by the asynchronous parallel
load capability of the circuit. Information present on the parallel data inputs (D0 to D3) is
loaded into the counter and appears on the outputs (Q0 to Q3) regardless of the
conditions of the clock inputs when the parallel load (PL) input is LOW. A HIGH level on
the master reset (MR) input will disable the parallel load gates, override both clock inputs
and set all outputs (Q0 to Q3) LOW. If one of the clock inputs is LOW during and after a
reset or load operation, the next LOW-to-HIGH transition of that clock will be interpreted
as a legitimate signal and will be counted. Inputs include clamp diodes. This enables the
use of current limiting resistors to interface inputs to voltages in excess of VCC.
2.
Features and benefits
Input levels:
For 74HC193: CMOS level
For 74HCT193: TTL level
Synchronous reversible 4-bit binary counting
Asynchronous parallel load
Asynchronous reset
Expandable without external logic
Complies with JEDEC standard no. 7A
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V.
74HC193; 74HCT193
Presettable synchronous 4-bit binary up/down counter
Rev. 4 — 24 June 2013
Product data sheet
相關PDF資料
PDF描述
74HCT1G125GW,165 IC BUS BUFF DVR TRI-ST 5TSSOP
74HCT1G126GW,165 IC BUS BUFF DVR TRI-ST 5TSSOP
74HCT393DB,118 IC DUAL 4BIT BINARY RIPPL 14SSOP
74HCT4020DB,112 IC 14STAGE BINARY RIPPLE 16-SSOP
74HCT4040PW,112 IC 12STAGE BINARY RIPPLE 16TSSOP
相關代理商/技術參數
參數描述
74HCT193DB-Q100J 制造商:NXP Semiconductors 功能描述:74HCT193DB-Q100/SSOP16/REEL13/ 制造商:NXP Semiconductors 功能描述:74HCT193DB-Q100/SSOP16/REEL13/ - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC COUNTER U/D 4BIT BIN 16SSOP
74HCT193DB-T 功能描述:計數器 IC 4-BIT BINARY UP/DOWN COUNTER RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel
74HCT193D-Q100J 制造商:NXP Semiconductors 功能描述:74HCT193D-Q100/SO16/REEL13// 制造商:NXP Semiconductors 功能描述:74HCT193D-Q100/SO16/REEL13// - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC COUNTER U/D 4BIT BIN 16SOIC
74HCT193M 制造商:HAR 功能描述:74HCT193
74HCT193N 功能描述:計數器 IC 4-BIT BINARY UP/DOWN COUNTER RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel
主站蜘蛛池模板: 阜宁县| 佛山市| 芦山县| 淮安市| 宁都县| 松阳县| 凤翔县| 三门峡市| 鸡西市| 望都县| 容城县| 梅河口市| 达孜县| 依兰县| 县级市| 即墨市| 乐东| 永泰县| 大新县| 晋州市| 昌邑市| 龙海市| 英德市| 卫辉市| 鹿泉市| 民和| 闸北区| 汉川市| 邵阳县| 沂水县| 罗山县| 界首市| 石门县| 丰城市| 翼城县| 屏东市| 独山县| 六安市| 江达县| 临沭县| 弥勒县|