- 您現在的位置：買賣IC網 > PDF目錄369351 > 78Q2120 (Electronic Theatre Controls, Inc.) 10/100BASE-TX Ethernet Transceiver PDF資料下載
參數資料
| 型號： | 78Q2120 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 10/100BASE-TX Ethernet Transceiver |
| 中文描述： | 10/100BASE-TX以太網收發器 |
| 文件頁數： | 9/33頁 |
| 文件大小： | 200K |
| 代理商： | 78Q2120 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
78Q2120
10/100BASE-TX
Ethernet Transceiver
OSCILLATOR/CLOCK
9
NAME
64-PIN
80-PIN
TYPE
DESCRIPTION
CKIN
4
5
I
CLOCK INPUT: Connects to a 25 MHz clock source. This pin should
be held low when XTLP and XTLN are being used as the 25 MHz
clock source.
XTLP,
XTLN
59, 58
75,74
A
CRYSTAL PINS: Should be connected to a 25 MHz crystal. When
CKIN is being used as the 25 MHz clock source, these pins should be
connected together.
MISCELLANEOUS PINS
GPIO0
-
19
I/O
GENERAL PURPOSE I/O PIN: This is an I/O pin which is
configurable as an input or an output via management interface. A
value of one in bit MR16.6 configures GPIO0 as an input, and a zero
configures it as an output. The logic level of the GPIO0 pin is reflected
in MR16.7. This pin has a weak internal pull-down to prevent it from
floating when configured as an input (it is configured as an input by
default).
GPIO1
-
20
I/O
GENERAL PURPOSE I/O PIN: This is an I/O pin which is
configurable as an input or an output via the management interface. A
value of one in bit MR16.8 configures GPIO1 as an input, and a zero
configures it as an output. The logic level of the GPIO1 pin is reflected
in MR16.9. This pin has a weak internal pull-down to prevent it from
floating when configured as an input (it is configured as an input by
default).
INTR
35
43
OZ
INTERRUPT PIN: This pin is used to signal an interrupt to the media
access controller. The pin is held in the high impedance state when
an interrupt is not indicated. The pin will be forced high or low to
signal an interrupt depending upon the value of the INTR_LEVEL bt
(MR16.14). The events which trigger an interrupt can be programmed
via the Interrupt Control Register located at address MR17.
POWER SUPPLY
V
CC
8, 11,
41, 43,
57, 63
10,13,
27,36, 49,
52, 59, 60,
73, 79 80
S
SUPPLY VOLTAGE: Two supply ranges are supported: 5V
±
0.5V, or
3.3V
±
0.3V.
GND
3, 5, 9,
10, 42,
53, 55,
60
4,7, 11,12,
28, 35, 50,
51, 65, 71,
76
S
GROUND
REFERENCE PIN
RIBB
56
72
A
BIAS CURRENT SETTING RESISTOR: To be tied to an external
resistor which is also connected to pin 70. This resistor should be
placed as close as possible to the package pin. See Figure 1 for
suggested value.
RIBB_RET
54
70
A
BIAS CURRENT SETTING RESISTOR RETURN PIN: To be
connected to external RIBB resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| 78Q2120-64 | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CG | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CGT | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64T | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-CGT | 10/100BASE-TX Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78Q2120-64 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CGT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120C | 制造商:TDK 制造商全稱:TDK Electronics 功能描述:10/100BASE - TX Transceiver |
發布緊急采購，3分鐘左右您將得到回復。