- 您現在的位置：買賣IC網 > PDF目錄369351 > 78Q8392L-CP (Electronic Theatre Controls, Inc.) Low Power Ethernet Coaxial Transceiver PDF資料下載
參數資料
| 型號： | 78Q8392L-CP |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low Power Ethernet Coaxial Transceiver |
| 中文描述： | 低功率以太網同軸收發器 |
| 文件頁數： | 2/12頁 |
| 文件大小： | 54K |
| 代理商： | 78Q8392L-CP |
78Q8392L
Low Power Ethernet
Coaxial Transceiver
2
FUNCTIONAL DESCRIPTION
The 78Q8392L incorporates six basic functions of
the Ethernet Transceiver, including
transmitting, collision signaling, collision detection,
jabber timing, and the heartbeat function. Refer to
Figure 1 for a general system block diagram.
receiving,
RECEIVER FUNCTIONS
The receiver senses signals through the RXI input,
which minimizes reflections on the transmission
media using a low capacitance, high resistance input
buffer amplifier. The CDS ground input attaches
directly to the input buffer from the coaxial shield to
eliminate ground loop noise.
In addition to the input buffer, the receiver data path
consists of an equalizer, data slicer, receiver squelch
circuitry, and an output line driver.
The equalizer improves the cable-induced jitter; the
data slicer restores equalized received signals to fast
transition signals with binary levels to drive the
receiver line driver; and the receiver line driver drives
the AUI cable through an isolation transformer that
connects to the AUI interface.
Noise on the transmission media is rejected by the
receiver squelch circuitry, which determines valid
data via three criteria: Average DC level, pulse width
and transition period. The DC voltage level is
detected and compared to a set level in the receiver
comparator circuit. The pulse width must be greater
than 20 ns to pass the narrow pulse filter; the
transition timer outputs a true level on the RX Data
Valid line provided the time between transitions is
less than about 200 ns. As long as a valid RXI signal
is detected, the output line driver remains enabled.
The transition timer disables the line driver when
there are no further transitions on the data medium,
and the RX+, RX- pins go to a zero differential
voltage state (Figure 3).
TRANSMITTER FUNCTIONS
The transmitter data path consists of a transmit input
buffer, pulse-shaping filter, transmit squelch
circuitry and transmit output line driver. The
self-biasing transmit input buffer receives data
through an isolation transformer and translates the
AUI differential analog signal to square pulse suitable
for driving the pulse shaping filter.
The filter outputs a correctly shaped and bandlimited
signal to the transmit output driver, which drives the
transmission medium through a high impedance
current source. When the transmitter is off, the
capacitance of the transmit driver is isolated from the
transmission media by an external diode with a low
capacitance node. The shield of the transmission
media serves as the ground return for the transmitter
function.
A transmit squelch circuit, which consists of a pulse
threshold detector, a pulse width detector, and a
pulse duration timer, is used to suppress noise, as
well as crosstalk on the AUI cable. The squelch
circuitry disables the transmit driver if the signal at
TX+ or TX- is smaller than the pulse threshold. Pulse
noise is rejected by a pulse width detector that
passes only pulses with durations greater than 20 ns.
The pulse duration timer disables the transmit driver
if no pulses are received for two-bit periods following
valid pulses. At the end of a transmission, the pulse
duration timer disables the transmitter and triggers
the blanking timer, used to block “dribble” bits.
COLLISION DETECTION
A collision occurs when two or more transmitters
simultaneously transmit on the transmission media. A
collision is detected by comparing the average DC
level of the transmission media to a collision
threshold. The received signal at RXI is buffered and
sent through a low pass filter, then compared in the
collision threshold circuit. If the average DC level
exceeds a collision threshold, a 10 MHz signal is
output on the CD± pins.
COLLISION SIGNALING
When collision signaling is enabled, a 10 MHz signal
is sent from the CD± pins through an isolation
transformer to the DTE. When the function is
disabled, this output goes to a zero differential state.
The 10 MHz output from the CD pins indicates a
collision on the transmission media, a heartbeat
function, or that the transmitter is in jabber mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 78S40 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 78S40 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 78SR100 | 1.5A Wide Input Positive Step-Down ISR Family |
| 78SR100SERIES | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 78SR106TC | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78Q8392L-DB | 制造商:TERIDIAN 功能描述:KIT 78Q8392L DEMO BOARD |
| 78Q8430 | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:10/100 Ethernet MAC and PHY |
| 78Q8430-100CGT/F | 制造商:TERIDIAN 功能描述:CONTROLLER 10/100 MAC+PHY 100LQFP 制造商:TERIDIAN 功能描述:CONTROLLER, 10/100 MAC+PHY, 100LQFP |
| 78Q8430-100CGTR/F | 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY |
| 78Q8430-100IGT/F | 功能描述:以太網 IC 10/100 Ethernet MAC & PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。