- 您現在的位置：買賣IC網 > PDF目錄294397 > 7P160FLF1401C20 VOLTAGE DETECTOR W/PUSH-PULL ACTIVE LOW OUTPUT & 0ms TIMEOUT, -40C to +125C, 4-SOT-143, T/R PDF資料下載
參數資料
| 型號： | 7P160FLF1401C20 |
| 英文描述： | VOLTAGE DETECTOR W/PUSH-PULL ACTIVE LOW OUTPUT & 0ms TIMEOUT, -40C to +125C, 4-SOT-143, T/R |
| 中文描述： | 周邊雜項 |
| 文件頁數： | 1/17頁 |
| 文件大?。?/td> | 202K |
| 代理商： | 7P160FLF1401C20 |
November 2000 Rev. 3 - ECO #13392
1
PCMCIA Flash Memory Card
FLF10 Series
PC Card Products
Low cost, high density Linear Flash
Card
Universal 3V to 5V operating range
providing full “plug and play”
exchangeability between different
systems
Based on Intel 28F128J3A (MLC)
Components
Fast Read Performance
- 250ns Maximum Access Time
- (200ns optional)
PCMCIA compatible
- x8/ x16 Data Interface
32-Byte Write Buffer (per Memory
Device)
- 6s per Byte Effective Write Time
128-bit Protection Register (per Memory
Device)
-64-bit Unique Device Identifier
-64-bit User Programmable OTP
Cells
Cross-Compatible Command Support
- Common Flash Interface (CFI)
- Intel Basic Command Set
- Scaleable Command Set
Power-Down Mode
- Reset, Power Down Registers
100,000 Erase Cycles per Block
128K word symmetrical Block
Architecture
PC Card Standard Type I Form Factor
WEDC’s Flash memory cards - FLF10 Series - offer high density
linear Flash memory for code and data storage, high performance
disk emulation, mobile PC and embedded applications.
The WEDC FLF10 series is based on Intel’s Multi Level Cell
(MLC) Flash memory technology, providing high density Flash
components at a significantly lower cost per megabyte. MLC
technology allows for two bits of information to be stored in a single
cell. This leads to reduced die size and reduced cost per megabyte.
WEDC’s FLF10 series cards are built with Intel’s 128Mb memory
component, 28F128J3A, with a manufacturer/device ID of 89/18
H.
The FLF10 series is available in densities of 32, 64, 96, 128, 160,
and 192MB.
WEDC’s FLF10 series provides densities from 32MB to 192MB, in
32MB increments. The cards up to the 64MB density operate in the
regular PCMCIA mode. The densities beyond the 64MB density
are implemented using a “paging scheme”, which is also supported
by the PCMCIA standard. By writing a page address to the
Configuration Option Register (address 4000H), an additional page
of memory can be accessed. The current FLF10 series supports
densities to 192MB: total of 3 pages: page 0 := 64MB, page 1 :=
64MB, and page 2 := 64MB.
The FLF10 series card operates in a wide, universal voltage range,
from 3V to 5V, allowing full “plug and play” functionality and
upgrade solutions in all mobile, battery powered applications.
Each memory component in the card also has a 128-bit Protection
Register, containing 64 bits of User Programmable OTP (One Time
Programmable) Cells.
These cells can be programmed with a
numeric security measure, such as an electronic signature.
To provide a 16 bit word wide access supported by the PCMCIA
standard, devices are paired on the card. Therefore, the Flash array
is structured in 128K word (256kB) blocks. Write, read and block
erase operations can be performed as either a word or byte wide
operation.
The FLF10 series cards conform to the PC Card 95 Standard
supported by PCMCIA and JEIDA, providing electrical and
physical compatibility. The PC Card form factor offers an industry
standard pinout and mechanical outline, allowing density upgrades
without system design changes.
WEDC’s standard cards are shipped with WEDC’s Flash Logo.
Cards are also available with blank housings (no Logo). The blank
housings are available in both, a recessed (for label) or flat housing.
Please contact your WEDC sales representative for further
information on Custom artwork.
High Density FLASH Memory Card
32, 64, 96, 128, 160, 192 MEGABYTE
General Description
Features
相關PDF資料 |
PDF描述 |
|---|---|
| 7P160FLF1401C25 | MICRO POWER VOLTAGE DETECTOR, W/PUSH PULL ACTIVE HIGH, -40C to +125C, 4-SOT-143, T/R |
| 7P160FLF1402C20 | Peripheral Miscellaneous |
| 7P160FLF1402C25 | VOLTAGE DETECTOR W/PUSH-PULL ACTIVE LOW OUTPUT & 2ms TIMEOUT, -40C to +125C, 4-SOT-143, T/R |
| 7P192FLF1200C20 | VOLTAGE DETECTOR W/PUSH-PULL ACTIVE LOW OUTPUT & 0ms TIMEOUT, -40C to +125C, 4-SOT-143, T/R |
| 7P192FLF1200C25 | Peripheral Miscellaneous |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7P16-2T12-1 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-2T12-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-2T24-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-3T24-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P-19.200MBP-T | 功能描述:19.2MHz Clipped Sine Wave, CMOS TCXO Oscillator Surface Mount 2.7 V ~ 5.5 V 10mA 制造商:txc corporation 系列:7P 包裝:剪切帶（CT） 零件狀態:有效 類型:TCXO 頻率:19.2MHz 功能:- 輸出:削峰正弦波，CMOS 電壓 - 電源:2.7 V ~ 5.5 V 頻率穩定度:±280ppb 工作溫度:-40°C ~ 85°C 電流 - 電源（最大值）:10mA 等級:- 安裝類型:表面貼裝 大小/尺寸:0.197" 長 x 0.126" 寬（5.00mm x 3.20mm） 高度:0.065"（1.65mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 電流 - 電源（禁用）（最大值）:- 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。